Hearth & Home PIER-DV36IN Installation Manual Download Page 57

Page: 57 / 78

Hearth & Home Technologies • PIER-DV36IN, ST-DV36IN Installation Manual • 2658-980 Rev. C • 4/22

Finishing

A. Facing Material

NOTICE:

Surface temperatures around the appliance

will become warm while the appliance is in operation.

Ensure finishing materials used for all surfaces (floor, walls,

mantels, etc.) will withstand temperatures up to 190

Risk of Fire!
DO NOT

apply combustible materials beyond the min-

imum clearances.

Comply with all minimum clearanc-

es to combustibles as specified in this manual.

terials overlapping into non-combustible zones could

ignite and will interfere with air flow through decorative

barrier fronts.

• Metal front of appliance may be covered with non-

combustible materials only.

• Facing and/or finishing materials must not interfere

with air flow through decorative barrier fronts, removal

of decorative barrier fronts or access for service.

• Facing and/or finishing materials must never

overhang into the glass opening.

• Observe all clearances when applying combustible

materials.

• Seal gaps between the finished wall and appliance

top and sides using a 300 ºF minimum sealant. Refer

to Figure 10.1 and Figure 10.2.

WARNING

Figure 10.1 Non-combustible Facing Diagram

0 in.

Finish wall material may be

combustible - Top and Sides

High Temperature Sealant (300° F/149° C min.)

Top and Side Seal Joint

= Factory-Installed Non-Combustible Board

If using vinyl flooring, refer to Section 3.E.

WARNING!

Risk of Overheating!

DO NOT

allow gap

between finishing materials and front of appliance.

Figure 10.2 Finishing Material Installed

FACTORY-INSTALLED

NON-COMBUSTIBLE BOARD

NON-COMBUSTIBLE

FINISHING MATERIAL

NO GAP ALLOWED

DRYWALL OR

WALL SHEATHING

MATERIAL

Summary of Contents for PIER-DV36IN















































































Search results

Summary of Contents for PIER-DV36IN

Reviews:

Related manuals for PIER-DV36IN

Brands by name

Popular brands

Hearth & Home PIER-DV36IN, Installation Manual

Search results

Summary of Contents for PIER-DV36IN

Reviews:

Related manuals for PIER-DV36IN

Brands by name

Popular brands