Hearth & Home PIER-DV36IN Installation Manual Download Page 27

Page: 27 / 78

Hearth & Home Technologies • PIER-DV36IN, ST-DV36IN Installation Manual • 2658-980 Rev. C • 4/22

Metal

Refractory Panel

To access the

exhaust opening,

remove the metal refractory

panel and exhaust baffle.

To remove metal refractory

panel, remove the two

screws on top. To remove

the exhaust baffle, remove

the three screws securing it.

Top Vent Application

Exhaust restrictor

Rear Vent Application

Note:

Be sure to re-

install the exhaust

baffle and metal refractory

panel after exhaust

restrictor installation.

Exhaust restrictor

Note:

Be sure to re-

install the exhaust

baffle and metal

refractory panel after

exhaust restrictor

installation.

Exhaust Baffle

= 60 ft. Max. (18.3 m)

= 3 ft. Min. (914 mm)

Top Vent - Vertical Termination

No Elbow

NOTE:

If installing a vertical vent/

termination off the top of the appli

ance, the optional vertical termina

tion baffle should be used.

Figure 4.16

Exhaust restrictors are recommended for these verti

cally terminated products which have excessive draft.

Exhaust restrictors will compensate for high draft, and

restore visual flame height. If the vent configuration has

a total vertical of 10-60 feet, an exhaust restrictor may

be needed. The exhaust restrictor can be located in the

appliance manual bag.

Exhaust restrictor Instructions

1. Remove metal refractory panel and exhaust baffle from

pilot side of appliance. To remove the refractory panel

use a 1/4 inch nut driver and remove the two screws

that secure it in place. To remove the exhaust baffle,

remove the three screws securing it in place. See Figure

4.17.

Figure 4.17

Summary of Contents for PIER-DV36IN















































































Search results

Summary of Contents for PIER-DV36IN

Reviews:

Related manuals for PIER-DV36IN

Brands by name

Popular brands

Hearth & Home PIER-DV36IN, Installation Manual

Search results

Summary of Contents for PIER-DV36IN

Reviews:

Related manuals for PIER-DV36IN

Brands by name

Popular brands