Hearth & Home PIER-DV36IN Installation Manual Download Page 51

Page: 51 / 78

Hearth & Home Technologies • PIER-DV36IN, ST-DV36IN Installation Manual • 2658-980 Rev. C • 4/22

Accessories Requirements

• This appliance may be used with a wall switch, wall

mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home Technologies approved

accessories should be done now to avoid reconstruction.

Follow instructions that come with those accessories.

Electrical Service and Repair

WARNING! Risk of Shock!

Label all wires prior to dis-

connection when servicing controls. Wiring errors could

cause improper and dangerous operation. Verify proper

operation after servicing.

WARNING! Risk of Shock!

Replace damaged wire with

type 105º C rated wire. Wire must have high temperature

insulation.

• Wire the appliance junction box to 110-120 VAC for

proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT

wire

IPI controlled appliance junction box to a switched circuit.

Incorrect wiring will override IPI safety lockout.

• Refer to Figure 8.2 IntelliFire Touch (IFT) Wiring Diagram.
• This appliance is equipped with an IntelliFire control valve

which operates on a 6 volt system.

B. Wiring Requirements
IntelliFire Touch

Ignition System Wiring

NOTICE:

Batteries should only be used as a power

source in the event of an emergency power outage.

Batteries should not be used as a primary long-term power

source. Batteries tend to corrode over time. When using

batteries as a power source, the

volt transformer must

be unplugged from the receptacle.

Do not store batteries in the battery pack when the

appliance is powered by the 6 volt transformer connected

to permanent electrical service.

Summary of Contents for PIER-DV36IN















































































Search results

Summary of Contents for PIER-DV36IN

Reviews:

Related manuals for PIER-DV36IN

Brands by name

Popular brands

Hearth & Home PIER-DV36IN, Installation Manual

Search results

Summary of Contents for PIER-DV36IN

Reviews:

Related manuals for PIER-DV36IN

Brands by name

Popular brands