Hearth & Home PIER-DV36IN Installation Manual Download Page 60

Page: 60 / 78

Hearth & Home Technologies • PIER-DV36IN, ST-DV36IN Installation Manual • 2658-980 Rev. C • 4/22

Figure 10.9 MSFR-36-BK Decorative Barrier Front

MODEL

FIT

FINISH MATERIAL

MAXIMUM

THICKNESS

SEE

FIGURE

PIER-DV36IN

Inside

4 IN.

10.8

ST-DV36IN

Inside

6 IN.

10.8

D. Decorative Barrier Front Dimensions for

Finishing

The MSFR-36-BK decorative barrier front is certified for

use with the ST-DV36IN and PIER-DV36IN. The MSEP-

36-BK end panel is approved for use with the PIER-

DV36IN. Only decorative barrier fronts certified for use

with these appliance models may be used. The MSFR-

36-BK and MSEP-36-BK are inside fit fronts.

Stop finishing material flush with opening.

FINISHING MATERIAL

DOOR

FINISHING MATERIAL

MODEL

FIT

FINISH MATERIAL

MAXIMUM

THICKNESS

SEE

FIGURE

PIER-DV36IN

Inside

4 IN.

10.9

Figure 10.10 PIER-DV36IN Decorative Barrier Front Finishing

Finish up to the appliance opening for best results.

Decorative Barrier Front

MSFR-36-BK (ST-DV36IN / PIERDV36IN)

See Figure 10.9.

Decorative Barrier End Panel

MSEP-36-BK (PIER-DV36IN Only)

See Figure 10.10.

FINISHING

MATERIAL

Summary of Contents for PIER-DV36IN















































































Search results

Summary of Contents for PIER-DV36IN

Reviews:

Brands by name

Popular brands

Hearth & Home PIER-DV36IN, Installation Manual

Search results

Summary of Contents for PIER-DV36IN

Reviews:

Brands by name

Popular brands