Hearth & Home PIER-DV36IN Installation Manual Download Page 54

Page: 54 / 78

Hearth & Home Technologies • PIER-DV36IN, ST-DV36IN Installation Manual • 2658-980 Rev. C • 4/22

Figure 8.4 Fan Location, Fan and Rheostat Wiring

Installation (Without Optional Remote)

1. Install and wire the fan in appliance as shown in Figure

8.4 and Figure 8.5.

2. Wire the fan temperature sensor and adjustable speed

control (rheostat switch) according to the instructions

provided with the fan.

3. Attach rheostat switch to the valve bracket.

BLUE

RHEOSTAT

SWITCH

TEMPERATURE

SENSOR

JUNCTION BOX

Figure 8.5 Detail of Fan Wiring with Rheostat

FAN

LOCATION

THREADED STUD USED TO

INSTALL TEMPERATURE SENSOR

RHEOSTAT

SWITCH

TEMPERATURE

SENSOR

JUNCTION

BOX

VALVE

BRACKET

Temperature Sensor Wiring for Optional Fan

If the fan will not be installed for operation with the IFT-

RC400, the temperature sensor will need to be installed.

See Figure 8.4 for location of the temperature sensor and

rheostat switch.
• The power supply for the appliance must be brought into

the junction box.

• Install rheostat switch in location as seen in Figure 8.4.
• Connect temperature sensor switch wire and rheostat

switch wires to junction box as shown in Figure 8.5.

C. Fan (Optional)

Installation (With Optional Remote)

1. Wire the fan as shown in Figure 8.3.
2. Locate the fan as shown in Figure 8.4.

Summary of Contents for PIER-DV36IN















































































Search results

Summary of Contents for PIER-DV36IN

Reviews:

Brands by name

Popular brands

Hearth & Home PIER-DV36IN, Installation Manual

Search results

Summary of Contents for PIER-DV36IN

Reviews:

Brands by name

Popular brands