background image

www.haywardpool.com              USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 

Max-Flo II

 ™

 Series__________ 

           _____                 ________________________ ______Page 5 of 16 

Product Specifications 

 

 
Installation Instructions 

 

 

WARNING –

 

This product should be installed and serviced only by a qualified professional.

 

 

 

 

 

 

  

 

Pump Location 

 

 

 

 

 

  

 

 

Locate pump as close to pool as practical and run suction lines as direct as possible to reduce friction 
loss.  Suction lines should have continuous slope upward from lowest point in line.  Joints must be tight 
(but not over-tightened).  Suction line diameter must equal or be larger than the discharge line diameter. 

 

Though the pump is designed for outdoor use, it is strongly advised to protect the electrical components 

from the weather.  Select a well-drained area, one that will not flood when it rains.  

Do NOT install pump in a damp or 

non-ventilated location.  

Keep motor clean.  Pump motors require free circulation of air for cooling.   

 

Pump Mounting 

 
Install pump on a firm, level base or pad to meet all local and national codes.  Fasten pump to base or pad with screws or 
bolts to further reduce vibration and stress on pipe or hose joints.  The base MUST be solid, level, rigid, and vibration free.  

 

 

 

Pump mount must: 

 

Allow pump inlet height to be as close to water level as possible. 

 

Allow use of short, direct suction pipe (to reduce friction losses). 

 

Allow for gate valves in suction and discharge piping. 

 

Be protected from excess moisture and flooding. 

 

Allow adequate access for servicing pump and piping. 

  

IMPORTANT NOTES

 – No system should allow any higher than 8-ft/sec [2.44 meters/sec]  

water velocity.   It is recommended that a minimum length of piping (L as shown to the right), equivalent  
to 5 pipe diameters, be used between the pump suction inlet and any plumbing fittings. 

 

Pipe Sizing Chart 

MAXIMUM RECOMMENDED SYSTEM FLOW RATE BY PIPE SIZE 

Pipe Size 

Flow rate 

Water Velocity 

Pipe Size 

Flow rate 

Water Velocity 

[mm] GPM 

[Liter/Min] 

ft/sec 

[meters/sec] [mm] GPM 

[Liter/Min] 

ft/sec 

[meters/sec] 

1 ½” 

50.76 

2 ½” 

119.40 

[50] [192] [2.44] [75] [452]  [2.44] 

2” 83.65  8  3” 184.32  8 

[63] [317] [2.44] [90] [698]  [2.44] 

 

Single Speed 

HP Dimension "A"

0.75

10.8" 

1 11.3" 

1.5

12.4" 

2 12.5" 

Dual Speed 

HP Dimension "A"

1 12.0" 

1.5

12.5" 

2 13.0" 

Summary of Contents for Max-Flo™

















Reviews: