Hayward only guarantees the quality, performance and safety of its products when assembled with genuine Hayward manufactured parts.
Use of non genuine Hayward manufactured parts will void all warranty.
K487BLU REV A
6
Hayward only guarantees the quality, performance and safety of its products when assembled with genuine Hayward manufactured parts.
Use of non genuine Hayward manufactured parts will void all warranty.
Step 4
The cleaner hose should reach from the skimmer or Hayward Vac Lock installed on the pool wall to the farthest point in
the pool plus two (2) extra hose sections. (The length of each hose section is four feet.) The total hose length supplied
(32 feet) which has been determined to be sufficient for the majority of pools nationally. This extra length is critical for
proper operation of the Hayward Blu cleaner. If the provided hose is not long enough, it will be necessary to purchase
additional hose sections from your Hayward dealer. After the correct hose length has been assembled, fill hose
completely with water. Insert (V574) flow gauge in to the leader hose, then attach the c-clip of the gauge onto the first
hose section. Make sure the flow gauge is under water. (See Figure 2)
Step 5
Turn the filter system on and allow it to run for several
minutes to eliminate any air in the system. Connect the
(V093C) skimmer cone to the tapered male end of the
vacuum hose if you are connecting the hose to your
skimmer. Then insert the cone into the suction port of
the skimmer (See Figure 3). If you are using a
Hayward Vac Lock installed on the pool wall, insert the hose
end directly into the Vac Lock fitting without using the cone.
(Refer to the
“
Important Tips
” section
for more specific
skimmer information).
K487BLU REV A
6
Hayward only guarantees the quality, performance and safety of its products when assembled with genuine Hayward manufactured parts.
Use of non genuine Hayward manufactured parts will void all warranty.
Step 4
The cleaner hose should reach from the skimmer or Hayward Vac Lock installed on the pool wall to the farthest point in
the pool plus two (2) extra hose sections. (The length of each hose section is four feet.) The total hose length supplied
(32 feet) which has been determined to be sufficient for the majority of pools nationally. This extra length is critical for
proper operation of the Hayward Blu cleaner. If the provided hose is not long enough, it will be necessary to purchase
additional hose sections from your Hayward dealer. After the correct hose length has been assembled, fill hose
completely with water. Insert (V574) flow gauge in to the leader hose, then attach the c-clip of the gauge onto the first
hose section. Make sure the flow gauge is under water. (See Figure 2)
Step 5
Turn the filter system on and allow it to run for several
minutes to eliminate any air in the system. Connect the
(V093C) skimmer cone to the tapered male end of the
vacuum hose if you are connecting the hose to your
skimmer. Then insert the cone into the suction port of
the skimmer (See Figure 3). If you are using a
Hayward Vac Lock installed on the pool wall, insert the hose
end directly into the Vac Lock fitting without using the cone.
(Refer to the
“
Important Tips
” section
for more specific
skimmer information).
K487BLU REV A
6
Hayward only guarantees the quality, performance and safety of its products when assembled with genuine Hayward manufactured parts.
Use of non genuine Hayward manufactured parts will void all warranty.
Step 4
The cleaner hose should reach from the skimmer or Hayward Vac Lock installed on the pool wall to the farthest point in
the pool plus two (2) extra hose sections. (The length of each hose section is four feet.) The total hose length supplied
(32 feet) which has been determined to be sufficient for the majority of pools nationally. This extra length is critical for
proper operation of the Hayward Blu cleaner. If the provided hose is not long enough, it will be necessary to purchase
additional hose sections from your Hayward dealer. After the correct hose length has been assembled, fill hose
completely with water. Insert (V574) flow gauge in to the leader hose, then attach the c-clip of the gauge onto the first
hose section. Make sure the flow gauge is under water. (See Figure 2)
Step 5
Turn the filter system on and allow it to run for several
minutes to eliminate any air in the system. Connect the
(V093C) skimmer cone to the tapered male end of the
vacuum hose if you are connecting the hose to your
skimmer. Then insert the cone into the suction port of
the skimmer (See Figure 3). If you are using a
Hayward Vac Lock installed on the pool wall, insert the hose
end directly into the Vac Lock fitting without using the cone.
(Refer to the
“
Important Tips
” section
for more specific
skimmer information).
220318_BluManual_r3.indd 6
1/14/13 1:27 PM