Hayward only guarantees the quality, performance and safety of its products when assembled with genuine Hayward manufactured parts.
Use of non genuine Hayward manufactured parts will void all warranty.
K487BLU REV A
5
Hayward only guarantees the quality, performance and safety of its products when assembled with genuine Hayward manufactured parts.
Use of non genuine Hayward manufactured parts will void all warranty.
To prepare your pool for your new Hayward Blu automatic cleaner installation, please follow the easy steps listed below.
After reading these instructions,
the “
Hayward Blu cleaner installation video will walk you through the installation process
step by step in addition to providing you with some routine maintenance and troubleshooting tips.
Step 1
Check the pool and remove any large objects that might interfere with the cleaner’s operation.
Check to see that the
water level is at the recommended level. Check the water chemistry to make sure that the water is properly balanced and
that the pool is free from algae. Algae can adversely affect the operation of the Hayward Blu cleaner and its overall
performance.
Step 2
Clean or backwash the filter and remove all debris from the pump basket prior to installing the Hayward Blu cleaner.
These pool equipment maintenance steps should be performed on a regular basis according to individual pool conditions
to maintain the optimal performance of your Hayward Blu cleaner.
Step 3
There are seven (7) connector hoses and one (1) leader hose with a hose cuff. The hose cuff has a orange sticker
attached to it that reads
“REMOVE LABEL AND CONNECT TO CLEANER”.
Connect the special Hayward Blu hose sections together by pushing and twisting the tapered male connector end of each
hose firmly into the open female end of the adjacent hose section (See Figure1). Depending on the size and shape of
your pool it may not be necessary to use all of the hose sections. However, the leader hose must be used or the Hayward
Blu cleaner will not operate properly. It is not necessary to bottom out the hose connections but they must be tight
enough to prevent any air leaks. Wetting the hose ends prior to putting them together will make it easier to assemble.
K487BLU REV A
5
Hayward only guarantees the quality, performance and safety of its products when assembled with genuine Hayward manufactured parts.
Use of non genuine Hayward manufactured parts will void all warranty.
To prepare your pool for your new Hayward Blu automatic cleaner installation, please follow the easy steps listed below.
After reading these instructions,
the “
Hayward Blu cleaner installation video will walk you through the installation process
step by step in addition to providing you with some routine maintenance and troubleshooting tips.
Step 1
Check the pool and remove any large objects that might interfere with the cleaner’s operation.
Check to see that the
water level is at the recommended level. Check the water chemistry to make sure that the water is properly balanced and
that the pool is free from algae. Algae can adversely affect the operation of the Hayward Blu cleaner and its overall
performance.
Step 2
Clean or backwash the filter and remove all debris from the pump basket prior to installing the Hayward Blu cleaner.
These pool equipment maintenance steps should be performed on a regular basis according to individual pool conditions
to maintain the optimal performance of your Hayward Blu cleaner.
Step 3
There are seven (7) connector hoses and one (1) leader hose with a hose cuff. The hose cuff has a orange sticker
attached to it that reads
“REMOVE LABEL AND CONNECT TO CLEANER”.
Connect the special Hayward Blu hose sections together by pushing and twisting the tapered male connector end of each
hose firmly into the open female end of the adjacent hose section (See Figure1). Depending on the size and shape of
your pool it may not be necessary to use all of the hose sections. However, the leader hose must be used or the Hayward
Blu cleaner will not operate properly. It is not necessary to bottom out the hose connections but they must be tight
enough to prevent any air leaks. Wetting the hose ends prior to putting them together will make it easier to assemble.
220318_BluManual_r3.indd 5
1/14/13 1:27 PM
