background image

29

   GUARANTEE

Toolstation products deliver reliable service for normal, household use in domestic settings. All 
Toolstation products are individually tested before leaving the factory.
If you are a consumer and you experience a problem with your Toolstation product, which is found 
to be defective due to faulty materials or workmanship  within the Guarantee Period, this Toolstation 
Guarantee will cover repair or - at the discretion of Toolstation – replacement with a functionally 
equivalent Toolstation product.
Your product is under guarantee for 2 year from the date of purchase or the date of delivery of the 
product, if later.

The guarantee is subject to the following provisions:

-   The guarantee does not cover accidental damage, misuse, cabinet parts, knobs, or consumable 

items.

-   The product must be correctly installed and operated in accordance with the instructions 

contained in this manual.

-   It must be used solely for domestic purpose.

-   The guarantee will be retendered invalid if the product is re-sold or has been damaged by 

inexpert repair.

-   Specifications are subject to change without notice.

-   The manufacturer disclaims any liability for the incidental or consequential damages.

-   The guarantee is in addition to, and does not diminish your statutory or legal rights.

CUSTOMER SUPPORT

www.coreservice.co.uk
Call us +44 01904 947568
Email: [email protected]

Made in China

Summary of Contents for 75716






























Reviews: