background image

6

Chassis Cable Installation: Hawkeye® 2 Power Connections

37

CHASSIS CABLE INSTALLATION

HAWKEYE® 2 POWER CONNECTIONS

1. Disconnect the battery switch by turning the battery disconnect switch below the catwalk near the cabin floor.
2. Locate the battery compartment under the catwalk outside of the cabin door.

FIGURE 3. RoGator Battery Compartment Location

3. Remove the walkway cover and the battery compartment cover.
4. Route the power and ground wires of the Hawkeye® 2 NCV power cable (P/N 115-2005-316) along the frame 

rail and then behind the cab to the battery compartment.

5. Route the power and ground wires into the battery compartment. Keep the breaker on the outside of the 

battery compartment.

6. Use zip ties to secure the breaker to the existing cables near the battery compartment.
7. Connect the red battery power lead to a positive battery terminal.
8. Locate the battery disconnect switch and remove the nut from the top-left terminal.
9. Connect the black battery ground lead to the negative bolt on the battery disconnect switch and reinstall the 

nut.

10. After the installation is complete, reconnect the battery disconnect switch before operating any equipment.

FIGURE 4. Battery Disconnect Switch Location 

Machine 

Battery Box 

Access

Battery Disconnect 

Switch

Summary of Contents for AGCO RoGator A Series























































Reviews: