manualshive.com logo in svg

HAUL MASTER 99900, Set Up And Operating Instructions Manual, Page: 10 / 20

Share
Download
HAUL MASTER 99900 Set Up And Operating Instructions Manual Download Page 10

FIguRE j

SMALL

LOCK

PIn

(51)

Slide and position the Wheel Bracket 

6. 

Assembly (39) at the bottom end 

nearest the ground.  

(See Figure K.)

FIguRE K

WHEEL

BRACKET

ASSEMBLY

(39)

Install the Small Lock Pin (51) so the 

7. 

Wheel Bracket Assembly (39) cannot 

move up the Slide Base (21).  The 

Wheel Bracket Assembly must be 

completely down and at the end of the 

Large Slide Base to install the Small 

Lock Pin.  

(See Figure L.)

FIguRE L

SMALL

LOCK

PIn

(51)

Unlatch the Wheel Bracket Assembly 

8. 

Lock (40) so the Wheel Bracket can 

tilt up.  If necessary, pull the Winch 

in, and tighten the Steel Cable (15A) 

enough for the Lock to release.  After 

the Lock releases, make sure there 

is enough slack in the Steel Cable for 

the Wheel Bracket to tilt fully up. 

(See Figure M.)

FIguRE M

LOCK

(40)

Push the motorcycle up to the Wheel 

9. 

Bracket Assembly (39) and push the 

front wheel into the Wheel 

SKU 99900          

For technical questions, please call 1-800-444-3353.          

Page 10

Summary of Contents for 99900





















Reviews:

No comments