29
User Controls
INB100005-1 (Rev 19)
IND100064-17
UTILITIES:
Selecting this function will enable the user to configure the OSD menu, define
hot keys, verify BIOS Firmware version and miscellaneous operations.
USER SETTING:
(Press “+” to access the sub-menu)
DPMS
: Disable / Enable the DPMS function.
DISPLAY INPUT
: Disable / Enable input source name upon power up.
AUTO SOURCE SELECT
: Off = Disable auto source select function. (Default setting)
Low = Auto source select enabled ONLY in power up.
High = Auto source select ALWAYS enabled.
FILTER
: Auto/On/Off - Signal Noise Reduction for Analog RGB1 Signal.
(Only available/functioning on custom models where required)
GAMMA
: 1.0 / 1.6 / 2.2 - Adjusts gamma on TFT display.
SERIAL ADRESS
: Set Serial Remote Channel from 0 to 15.
(Consult “Serial Communication (SCOM) Interface” chapter in this manual
or the online “Serial Control Interface - MMD / MMC” manual for
complete instructions.)
OSD SETTING:
(Press “+” to access the sub-menu)
OSD HORZ POSITION:
Position the OSD menu horizontally.
OSD VERT POSITION:
Position the OSD menu vertically.
OSD BACKGROUND
: Choose between Translucent or Opaque.
OSD ROTATE
: Choose between Normal / Rotate. Will position the menu
either horizontally or vertically.
OSD MODE
; Only available in Advanced/Full menu!
“NORMAL” = ALWAYS shows the Simplified version of the
OSD menu. JHD logo will be shown in the top left corner.
“TOGGLE” = ALWAYS show the Advanced/Full version of the
OSD menu. JHD logo will NOT be shown in the top left corner.
(Please refer to the beginning of this chapter for information)
USER TIME OUT
: Adjust the OSD menu time out period in a step of 5 seconds.
ZOOM:
(Press “+” to access the sub-menu)
ZOOM LEVEL:
Zooms in the display area from center.
HORIZONTAL PAN:
Pan the display area horizontally.
VERTICAL PAN:
Pan the display area vertically.
DIRECT ACCESS 1 & 2:
(Press “+” to access the sub-menu)
Define the hot key function (“+” or “-” front/under hatch buttons) to one of these OSD functions:
Brightness / Contrast / Zoom / Video Source / PIP* / No Function / Test Pattern
* By pressing the assigned hot key, the sequence of the selected input video source are:
Analog RGB1 / Analog RGB2 / DVI / Composite Video / S-Video.
NOTE:
When assigning video source to hot key function, please set the “AUTO SOURCE SELECT” to HIGH (see above).
NOTE:
Direct Access 1 default factory setting is NO FUNCTION
NOTE:
Direct Access 2 default factory setting is NO FUNCTION
OSD Menu Functions
4
2
1
4
2
3
4
2
1
4
2
3
1
4
2
3
Summary of Contents for JH 10T06 MMD
