INSTALLATION
7
Form No. TMCEM-0404
ASSEMBLY
1. Remove unit from box.
2. Remove information packet.
To prevent delay
in obtaining warranty coverage, fill out and mail
in warranty card to Hatco
.
3. Remove tape from Discharge Chute, Crumb Tray and Toast
Collector Pan. See 4 .
4. If unit is not level, use 14 mm (9/16") open-end wrench
to adjust the foot of each leg until unit is level.
LOCATION
CAUTION
Do not locate the toaster in an area subject to excessive
temperatures or grease from grills, fryers, etc. Excessive
temperatures could cause damage to the unit. Do not place
toaster in an area that restricts air flow around the front or rear
of the unit. Do not place toaster in direct discharge path of air
conditioning vent or makeup air vent.
WARNING
For safe and proper operation, the unit must be located
a reasonable distance from combustible walls and materials.
If safe distances are not maintained, discoloration
or combustion could occur. Do not locate toaster under shelving
or closer than 305 mm (12") from the ceiling.
WARNING
To assure safe and proper operation while operating
in the Front Discharge mode, allow a minimum clearance
of 25 mm (1") along the sides and rear. Allow a minimum
clearance of 305 mm (12") along the front.
WARNING
To assure safe and proper operation while operating
in the Rear Discharge mode, allow a minimum clearance
of 25 mm (1") along the sides. Allow a minimum clearance
of 305 mm (12") along the front and rear.
CAUTION
To avoid any injury or damage locate the unit at the proper
counter height, in an area that is convenient for use.
The location should be level to prevent the unit or its contents
from accidentally falling, and strong enough to support
the weight of the unit.
CAUTION
Do not place anything on top of the toaster; doing so could
damage toaster or subject personnel to possible injury.
SET-UP
CAUTION
Unit is not weatherproof. For safe and proper operation the unit
must be located indoors where the ambient air temperature
is a minimum of 70°F (21°C) and a maximum of 85°F (29°C).
CAUTION
The toasting of coated or buttered products such as garlic
bread, cheese sandwiches and sweet rolls is NOT recommended.
Residue will reduce toaster performance and could possibly
ignite inside the toaster.
CAUTION
When setting up the unit for operation, make sure power
to the unit is off and the toaster is at room temperature. Failure
to do so could result in personal injury.
Toast Feed Ramp
The toast feed ramp is installed at the factory and can be used
in two positions. See 6 .
1. When in the upright position, the toaster is set for automatic
feed. Bread products enter the toaster by placing them
on the feed ramp and releasing.
2. For manual feeding of product, tip the feed ramp until it rests
on top of the unit. In this position bread products can be
manually loaded by placing directly on the conveyor belt.
CAUTION
Some exterior surfaces on the unit will get hot. Use caution
when touching these areas to avoid injury.
Toast Crumb Tray
Install toast crumb tray directly below the conveyor belt and below
the stop pins. Insert until the front of the crumb tray meets the stop
pins. See 7 .
CAUTION
To avoid damage to the unit or injury to personnel always
operate toaster with crumb tray installed.
CAUTION
To avoid any injury, do not remove the crumb tray for cleaning
until toaster is cool.
Front or Rear Discharge
Toast-Max units can be set up so toasted product discharges
at either the front or the rear of the unit.
For
front discharge
install toaster chute from the front
of the toaster with the curved end inward and the rear lip
of the chute on the rear most pins. See 8 . The discharge vane
must be in the closed position. See 9A .
For rear discharge
do not use the discharge chute. If the chute
is installed remove it. To set-up toaster for rear discharge position,
install the collector pan, with the open end first, over the set of pins
at the rear of the unit. Align the straight notches over the pins
and lower into place. The discharge vane must be in the open
position. See 9B .
Summary of Contents for Toast-Max TM-10H
Page 41: ...40 Form No TMCEM 0404 NOTES...
Page 42: ...41 Form No TMCEM 0404 NOTES...
Page 43: ...42 Form No TMCEM 0404 NOTES...
