8
Form No. GRCmWm-1216
MAINTENANCE
English
General
The Glo-Ray
®
merchandising Warmer is designed for maximum
durability and performance, with minimum maintenance.
ELECTRIC ShOCK hAzARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on the unit.
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Use only Genuine hatco Replacement Parts when
service is required. Failure to use Genuine hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in hatco equipment.
This unit has no “user-serviceable” parts. If service is
required on this unit, contact an Authorized hatco Service
Agent or contact the hatco Service Department at
800-558-0607 or 414-671-6350.
Daily Cleaning
To preserve the finish of the Glo-Ray merchandising Warmer,
perform the following cleaning procedure daily.
Use non-abrasive cleaners and cloths on glass and metal
surfaces. Abrasive cleaners and cloths could scratch the
finish of the unit, marring its appearance and making it
susceptible to soil accumulation.
IMPORTANT—DO NOT use paper towel or glass cleaner to
clean polycarbonate surfaces. Paper towel and glass
cleaner may scratch the material. Wipe off polycarbonate
surfaces using a soft, clean, water-dampened cloth.
NOTE: The sneeze guard, side panels, and back mirror glass
panel are removable for cleaning. Reverse the
procedures in the
INSTaLLaTION
section of this
manual for removal.
1. move the Power Switch to the “Off” position and unplug the
power cord. allow the unit to cool.
2. Wipe all metal surfaces with a damp, non-abrasive cloth.
Stubborn stains may be removed with a good non-abrasive
cleaner. Hard to reach areas can be cleaned using a small
brush and mild soap.
3. Clean the glass side panels and back mirror glass panels
using ordinary glass cleaner and a damp, soft cloth or
paper towel.
4. Clean the polycarbonate sneeze guard, doors, and side
panels (if equipped) using a mild, soapy water solution and
a damp, soft cloth.
NOTICE
: DO NOT use paper towel
.
WARNING
NOTICE
Replacing Xenon Display Light Bulbs
The warmer is equipped with two Xenon display lights to
illuminate the warming area. Use Hatco P/N R02.30.171.00
when replacing a Xenon light bulb.
NOTE: Light bulbs supplied by Hatco are designed specifically
for this application. Use of light bulbs not supplied by
Hatco will void the unit warranty.
Use the following procedure to replace a Xenon light bulb.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Pull the wire guard out of the display lamp housing.
3. Remove the old Xenon display light bulb from the light
socket.
a. Push and rotate the bulb in the socket until the tabs on
bulb are clear of the locking channels on the socket.
b. Pull the bulb out of the socket.
4. Install a new Xenon display light bulb into the light socket.
a. Push the bulb into the socket until the tabs on the bulb
align with the locking channels on the socket.
b. Turn the bulb so that the tabs on the bulb lock into the
locking channels on the socket.
5. Replace the wire guard into the display light housing.
Replacing the Display Light Bulbs
Wire
Guard
Xenon
Light Bulb
