10
Form No. DCSm-0214
MAINTENANCE
English
General
Hatco Decorative Carving Stations are designed for maximum
durability and performance, with minimum maintenance.
ELECTRIC SHOCK HAzARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no “user-serviceable” parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350; fax 800-690-2966; or
International fax 414-671-3976.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
Use non-abrasive cleaners on glass and metal surfaces.
Abrasive cleaners could scratch the finish of the unit,
marring its appearance and making it susceptible to soil
accumulation.
Daily Cleaning
For sanitary operation as well as to preserve the condition of the
unit and maintain performance, it is recommended that the unit
be cleaned daily.
NOTE: Before turning on the unit each day, clean and sanitize
the stone surfaces using a sanitizer approved for food
contact surfaces.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Clean the glass sneeze guard using paper towel and
standard glass cleaner.
3. Wipe down the lamp shade and all other metal parts with
a clean, soft, damp cloth. Stubborn stains can be removed
with a mild, non-abrasive cleanser.
4. Clean and sanitize the stone surfaces using a clean, damp
cloth and a sanitizer approved for food contact surfaces. If
additional cleaning is necessary, refer to the “Cleaning the
Stone Surface” information in this section.
NOTE: To correct inconsistent staining and discoloration, refer
to the “Cleaning the Stone Surface” information in this
section.
WARNING
NOTICE
Cleaning the Stone Surface
Proper use of the products listed below will not damage the
stone surface (follow the directions on the product labels).
NOTE: Stone surfaces are a simulated stone solid surface.
Make sure to clean and sanitize the stone surface properly
after deep cleaning the surface using abrasives and before
placing food product on unit.
Hard to Remove Stains
For hard-to-remove stains, use the supplied abrasive pad along
with an abrasive cleaner such as Ajax, Comet, Bon Ami, or Bar
Keeper’s Friend. Additional abrasive pads are available from
Hatco (P/N 04.39.049.00).
NOTICE
: Use supplied abrasive
pad on stone surface only.
NOTE: Do not use steel wool or metal scouring pads.
Mineral Based Stains
For a mineral-based stain, cleaners designed to remove iron or
rust are recommended and should not harm the stone surface.
Scratches
For scratches, use sandpaper starting with the coarsest grit and
going to finest grit until the scratch disappears. Blend area in
with the supplied abrasive pad.
Replacing a Heat Bulb
The heat lamps on the Decorative Carving Stations come
standard with a clear, coated infrared heat bulb rated at 250 W.
Use only heat lamps that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of heat lamps
not specially protected could result in personal injury
and/or food contamination.
To replace a bulb:
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Unscrew the heat bulb from the unit and replace with a new
bulb (bulbs have a threaded base).
The following replacement bulbs are available from the factory
or a Hatco Authorized Parts Distributor:
250 W, 120 V, Clear Coated
02.30.069.00
250 W, 120 V, Red Coated
02.30.068.00
WARNING
CAUTION
