background image

 

G1 SCBA Radio Pairing Guide | 

Harris

 

 

 

 

 

 

Rev. 5-23-2019 

Page 

8

 of 

13

 

 

 

 
 

Pairing a G1 SCBA and Harris XL-185P | XL-200P Radio 

 

Ensure the Harris Radio is programmed correctly to connect with the G1 SCBA.  Necessary and recommended settings are 

listed in the “Harris Configuration Settings” page.  Consult with your Radio Technician.   

Step 1.

 

  

Turn on the Harris Radio using the volume knob. 

 

Step 2.

 

 

Verify that Bluetooth is “ON” the radio Bluetooth icon is visible on radio 

display.  

If not visible, enable the radio’s Bluetooth (See Page 6, Step 6, for 

details) OR reconfigure radio.

 

 

Step 3.

 

 

Make the Radio 

Bluetooth

 

Discoverable

Note:   Every time you power on the Harris XL-185P | XL-200P, it starts up 

with Discoverability set to OFF

.  

Follow this procedure to turn it ON.

 

If you left the Bluetooth Utility Menu, navigate back to it using the procedure 

found on 

Page 6,

  

Step 6.

 method 

(B) steps “a.” through “d.”

, and then:

 

(D)

 

Up or Down arrow until “Discoverable” is highlighted 

(E)

 

Press the menu button in the Center of the arrow pad to change to 

“YES” 

** STAY ON THIS SCREEN **  

Leaving the Bluetooth menu will turn 

discoverability OFF again, and pairing will fail.   
To keep “Discoverable = YES” you must stay on this screen.

 

 

 

 

 

 

** STAY ON THIS SCREEN ** 

 

Step 4.

 

 

Press & hold

 either of the 

green

 

Control Module buttons to activate the RFID 

mode. 

 

For iTic Control modules: Press & Hold Both Green Buttons. 

 

          

 

 

Step 5.

 

 

Register the Radio to the SCBA:

  Place the Harris Radio 

Pairing Tag

 over the 

G1 Power Module 

RFID Target

After the pairing tag is successfully read, a Bluetooth enabled G1 SCBA will 

search for a pairing partner for 8 minutes. The pairing process should be 

repeated if 8 minutes is

 

exceeded

 

 

 

 

 

Pairing G1 & 

Radio 

Summary of Contents for XL-185P














Reviews: