Harmonic Drive SHG Series Manual Download | Manualshive

Page: 50 / 69

background image

50

1021387 12/2018

V02

5. Installation and Operation

5.1 Transport and Storage

Gears should be transported in the original packaging. If the gear is not put into service immediately on receipt, it should be
stored in a dry area in the original packaging. The permissible storage temperature range is -20 °C to + 60 °C.

5.2 Gear Condition at Delivery

The gears are generally delivered according to the dimensions indicated in the confirmation drawing.

Gears with Grease Lubrication

• SHG-2UH

These units are supplied with a lifetime lubrication as standard.

• SHG-2SO und SHG-2SH

These units are supplied without lifetime lubrication. Before commissioning of the unit an initial lubrication has to be applied
by the customer. A recommendation for the lubricant type can be found at chapter 4.10.1 and the recommended amount of
grease at chapter 5.5.2.

Gears with Oil Lubrication

Harmonic Drive® Units with oil lubrication are generally customer-specific solutions. Please follow the notes given on the
confirmation drawing. The oil temperature during operation must not exceed 90 °C. Oil must be filled into the unit by the
customer as the standard delivery does not include any oil lubricant.

Oil Quantity

The values specified in the confirmation drawing include the valid oil quantities to fill in. The oil quantity defined on the
confirmation drawing must be obeyed in any case. Too much oil results in excessive heat production and early wear due to the
thermal destruction of the oil. If the oil level is too low, this may lead to early wear as a result of lubricant deficiency.

5.3 Assembly Information

ADVICE

Screws which have been tightened by the gear manufacturer must not be loosened.

«
...
48
49
50
51
52
...
»

Summary of Contents for SHG Series






































































Reviews:

No comments

Related manuals for SHG Series

Brand: Camozzi Pages: 2

Brand: Oktober Pages: 22

Brand: Bard Pages: 144

Brand: GALBIATI Pages: 8

Brand: Vahva Jussi Pages: 9

Brand: VBM Pages: 36

Brand: W&H Med Pages: 122

Brand: IFM Pages: 175

Brand: IFM Pages: 5

Brand: JBL Pages: 38

Brand: JBSYSTEMS Light Pages: 32

Brand: JBM Pages: 12

Brand: Maico Pages: 55

Brand: Maico Pages: 38

Brand: Maico Pages: 2

Brand: MAHA Maschinenbau Haldenwang Pages: 13

Brand: Rain Harvesting Pages: 2

Brand: Yamaha Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands