Harmonic Drive SHG Series Manual Download | Manualshive

Page: 5 / 69

background image

5

1021387 12/2018

V02

1.1 Description of Safety Alert Symbols

Symbol

Meaning

Indicates an imminent hazardous situation. If this is not avoided, death or
serious injury could occur.

Indicates a possible hazard. Care should be taken or death or serious injury may
result.

Indicates a possible hazard. Care should be taken or slight or minor injury
may result.

Describes a possibly harmful situation. Care should be taken to avoid damage
to the system and surroundings.

This is not a safety symbol. This symbol indicates important information.

Warning of a general hazard. The type of hazard is determined by the
specific warning text.

Warning of dangerous electrical voltage and its effects.

Beware of hot surfaces.

Beware of suspended loads.

Precautions when handling electrostatic sensitive components.

Beware of electromagnetic environmental compatibility.

1.2 Disclaimer and Copyright

The contents, images and graphics contained in this document are predected by copyright. In addition to the copyright, logos,
fonts, company and product names can also be predected by brand law or trademark law. The use of text, extracts or graphics
requires the permission of the publisher or rights holder.

We have checked the contents of this document. Since errors cannot be ruled out entirely, we do not accept liability for mis-
takes which may have occurred. Notification of any mistake or suggestions for improvements will be gratefully received and any
necessary correction will be included in subsequent editions.

DANGER

WARNING

ATTENTION

INFORMATION

ADVICE

«
...
3
4
5
6
7
...
»

Summary of Contents for SHG Series






































































Reviews:

No comments

Related manuals for SHG Series

Brand: Tanaka Pages: 20

Brand: Tandem Pages: 80

Brand: Tanco Pages: 4

Brand: Grundfos Pages: 43

Brand: ABS Pages: 17

Brand: American DJ Pages: 8

Sure Stripe 3650

Brand: AIRLESSCO Pages: 14

Brand: Civemasa Pages: 55

Brand: Heitronic Pages: 16

DRIP IRRIGATION KIT

Brand: DAYLIFF Pages: 2

Brand: Garmin Pages: 8

Brand: OttLite Pages: 2

Brand: ReneSola Pages: 1

Brand: Agnetix Pages: 8

Brand: iSolution Pages: 4

PM-BT-E38xx1W2-R10 Series

Brand: IEI Technology Pages: 15

Brand: Abilica Pages: 55

Brand: probst Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands