Harmonic Drive SHG Series Manual Download | Manualshive

Page: 57 / 69

background image

57

1021387 12/2018

V02

5.7.3 Mounting the Wave Generator (WG) to the Motor Shaft

The axial position of the Wave Generator in the gearbox is critical for the correct operation of the unit. Please check the
correct position of the Wave Generator against the confirmation drawing.

• Push the greased Wave Generator onto the motor shaft according to the assembly dimension given in the confirmation

drawing. If there is no assembly value given, the Wave Generator must be moved until it reaches the shaft collar.

• Insert the plug into the bore of the Wave Generator Hub and tighten with the screw. When a clamping element is used,

tighten its screws in five steps to the torque given in the confirmation drawing. Final control of the assembly. Some
types of clamping elements can move axially during tightening. Adjust as appropriate.

1)

2)

7)

6)

3)

5)

4)

1) Ball Separator
2) Wave Generator Bearing
3) Wave Generator Plug
4) Insert
5) Thrust washers
6) Snap ring
7) Wave Generator Hub

5.7.2 Wave Generator Components SHG-2SO

Illustration 57.1 shows a standard Wave Generator with Oldham Coupling.

Illustration

57.1

«
...
55
56
57
58
59
...
»

Summary of Contents for SHG Series






































































Reviews:

No comments

Related manuals for SHG Series

Brand: ParaBody Pages: 5

Brand: Sagola Pages: 20

Brand: Earmor Pages: 5

Brand: parr Pages: 20

Brand: Landoll Pages: 71

Brand: York Fitness Pages: 4

Brand: W&H Pages: 23

Brand: Bartscher Pages: 24

Brand: CAIRE Pages: 2

Brand: NEILPRYDE Pages: 53

Brand: JAC Pages: 103

Brand: 3Disc Pages: 12

Brand: p-light Pages: 28

Brand: Varytec Pages: 5

Brand: Saab Pages: 98

Brand: Kaixin Pages: 89

MIAMI J ADVANCED

Brand: Össur Pages: 35

Brand: Össur Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands