Harmonic Drive SHG Series Manual Download

Page: 28 / 69

1021387 12/2018

V02

Ratio =

Reduction gearing

CS  Fixed
WG  Input
FS  Output

Reduction gearing

FS  Fixed
WG  Input
CS  Output

Reduction gearing

WG  Fixed
FS  Input
CS  Output

Differential gear

Control input

Main drive input

Main drive output

Numerous differential functions can be obtained by combinations of the speed and rotational direction of the three basic elements.
Please refer to our broshure “Differential Applications” available to download from our website.

Input and output rotate in opposite directions.

Input and output rotate in same direction.

Equation 28.1

Equation 28.4

Equation 28.2

Equation 28.5

Equation 28.3

Equation 28.6

Speed increaser gearing

Fixed

CS Input

FS Output

Speed increaser gearing

CS  Fixed
FS  Input
WG  Output

Speed increaser gearing

FS  Fixed
CS  Input
WG  Output

Input and output rotate in same direction.

Input and output rotate in opposite directions.

Input and output rotate in same direction.

Ratio

Ratio =

i + 1

Ratio =

i + 1

Ratio =

i + 1

Ratio =

i + 1

Summary of Contents for SHG Series






































































Search results

Summary of Contents for SHG Series

Reviews:

Related manuals for SHG Series

Brands by name

Popular brands

Harmonic Drive SHG Series, Manual

Search results

Summary of Contents for SHG Series

Reviews:

Related manuals for SHG Series

Brands by name

Popular brands