background image

Compact Stagebox

10  

Document generated: 12.02.13

SW V4.1

Setup Examples

3.1 

Compact Stagebox and Studer Consoles

 

Note

 

The example below shows the setup with the NanoSCore of a Studer OnAir 

1500 console, but applies in a similar way with other Studer consoles, see 

the table below.

 

  

Compact Stage Box

Studer OnAir 1500 Core

with optional MADI card in the D21m extension slot

Optical or RJ45 Cables

depending on MADI card type

Mains In 1

Mains In 2

Mains In

24 VDC In

Switch set to MAIN or AUX if using one 

cable, to RED if using 2 cables.

Studer Console

OnAir 1500

OnAir 2500

OnAir 3000

Vista 1

Vista 5-9

Stagebox 

support

SW V5.0 and up

SW V5.0 and up

SW V5.0 and up

SW V4.8 and up

(see chapter 3.2)

SW V4.703 and up

Stagebox 

connected to...

D21m MADI card in 

Nano SCore

integrated optical 

MADI I/O

D21m MADI card in 

SCore Live

D21m MADI card in 

console extension slot

D21m MADI card in 

SCore Live

Details

see drawing above

see ‘Note’ below

-

Select appropriate 

configuration

(see chapter 3.2.1)

-

 

 

  Before inserting the MADI I/O card into your console or its DSP core, remem-

ber to power it down and unplug it from the AC supply.

 

  After powering the system on again, please note that the added inputs and 

outputs need to be patched to the console’s logical inputs and outputs.

 

Note

  The Studer OnAir 2500 console features no D21m card slot. Its built-in optical 

MADI interface may be used for the connection to the Compact Stagebox. To 

do so, the Compact Stagebox 

must

 be equipped with a MADI HD card with 

optical

 connectors. Up to 64 inputs and 56 outputs can be added in this way.

Summary of Contents for STUDER



































Reviews: