manualshive.com logo in svg

Harken 1111 HL, User And Maintenance Manual

Share
Download
Harken 1111 HL User And Maintenance Manual Download Page 16

                                                                                                                                                                                                                     

User and maintenance manual Winch 1111 HL 

–

 Mod.A 

 

13.2 Installation procedure 

 

A.

 

Place the drilling cut-out template over the point chosen for installation.  

 
The template in DWG format for Winch 1111 HL is available on request from the Harken 
Italy Tech Service at 

[email protected]

. 

 
Small-scaled mounting template for Winch 1111 HL versions is shown below. 
For mounting templates of custom Winch 1111 HL version, refer to the boat custom 
manual provided by Harken.  
 

 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

For 1:1 mounting templates, contact Harken at 

[email protected]

 

 

VIEW FROM ABOVE 

MOUNTING TEMPLATE 

Summary of Contents for 1111 HL










































Reviews:

No comments

Brands by name

Popular brands

Load more brands