HARBEN CENTURY, Service Manual

Page: 76 / 83

SECTION A-A
A
A
PARTS LIST
DESCRIPTION QTY PART NUMBER ITEM
PIN SPIRAL TYPE 8MM X 16MM LG STAINLESS STEEL. 2 014007 1
PIN CLEVIS
1
014008 2
CLIP CLEVIS MK2 CENTURY SELECTOR 1 014009 3
O RING BS016 PTFE 1 015021 4
STEP SEAL 19.0MM DIA SHAFT C/W BS111/90 O RING 2 015022 5
O RING BS027/90 4 015023 6
KNOB PLASTIC 1032 M8 (SELECTOR LEVER) 1 023002 7
BODY MK2 CENTURY SELECTOR 1 036020 8
SPINDLE MK2 CENTURY SELECTOR 1 036021 9
NUT RETAINING MK2 CENTURY SELECTOR 1 036022 10
LEVER MK2 CENTURY SELECTOR 1 036023 11
GLAND MK2 CENTURY SELECTOR 2 036024 12
SEAT MK2 CENTURY SELECTOR 2 036025 13
COLLAR MK2 CENTURY SELECTOR 3 036026 14
LINK MK2 CENTURY SELECTOR 1 036027 15
2004
DRAWN
CHECKED
APPROVED
SCALE
WEIGHT
FINISH:
TITLE
DRG NO
PART NO
ISSUE
DATE
DRAWN
CHECKED
STATUS
TEST
INFORMATION FOR ESTIMATION OF WEIGHT AND COST ONLY
MATERIAL LIST
ITEM PART NO. MATERIAL SPEC SIZE
WT
mm Kg Kg/M
LENGTH TOTAL WT
QTY.
PARTS LIST
ITEM PART No. DRG. No QTY DESCRIPTION REMARKS
EXPOSED
AREA
PROTECTION
USED ON
SUPERSEDES/SUPERSEDED BY
A B C D E F G H J K
L M N P R S T U V W
X Y Z
Gemini House, Brunel Rd, Churchfields,
Salisbury, Wiltshire, England. SP2 7PU
Tel: (01722) 325424 Fax: 01722 411329
ALL DIMENSIONS IN MILLIMETRES
GEOMETRICAL TOLERANCES TO BS 308
ANGULAR DIMS TO BE WITHIN:-
MACHINED 0.5 , BENDING 2
THREADS: BSP, TO MED. FIT. B.S. 2779
ISOMETRIC TO 6g / 6H
TOLERANCES TO BE AS SPECIFIED BELOW UNLESS OTHERWISE STATED
30 UP TO AND INCLUDING
FABRICATION
UNMACHINED
* DELETE
ONE
RANGE
0.5
* MEDIUM
MACHINING
* FINE
MACHINING
0.3
0.1
OVER
0
100 2000 1000 300
SURFACE ROUGHNESS: 1.6 MICRONS Ra
CONCENTRICITY TO WITHIN 0.2 T.I.R.
M/C RADII 1.5
DRILLED HOLES +0.13/-0.00
HOLE CENTRES TO BE 0.2
REMOVE ALL BURRS & SHARP EDGES.
2.0
1.0
0.3
1.0 1.5
0.5
0.15
0.7
0.2
3.0 3.0
1.5
0.5
2.0
0.8
300 30 100 1000 2000
DATE
DATE
DATE
DO NOT SCALE
IF IN DOUBT ASK !
MANUFACTURERS UNABLE TO COMPLY MAY
SUBMIT ALTERNATIVES WHEN QUOTING.
ALL DRAWINGS NOT TO THE LATEST
ISSUE ARE TO BE DESTROYED.
Flowplant Group Ltd.
C COPYRIGHT Flowplant Group Ltd.
THIS DRAWING IS CONFIDENTIAL AND IS SUPPLIED
ON THE EXPRESS CONDITION THAT IT IS NOT
COPIED OR COMMUNICATED TO OTHER PERSONS
OR COMPANIES WITHOUT WRITTEN PERMISSION
FROM
FLOWPLANT GROUP LTD.
A
B
C
D
E
F
2 1 3 4 5 6 7 8
A
B
C
D
E
F
CALC
Third angle projection
L E A D E R S I N C L E A N I N G T E C H N O L O G Y
HEAT TREATMENT
60
1
9
6
8
2
10 9 5 5 4
12 6
14
13 6 13 6 12 6 8
7 11 15
2 1 3 1
HIGH PRESSURE INLET
1/2" BSP
LOW PRESSURE OUTLET
1/2" BSP
HIGH PRESSURE OUTLET
1/2" BSP
Fig. 4.
8
- Selector Mk2 - Century
73