HAPRO Luxura V10, Manual

Page: 5 / 160

5
ENGLISH
Congratulations on the purchase
of your Hapro sunbed. Your new
sunbed has been manufactured with
the utmost care and attention and
consists of high-quality parts. All Hapro
sunbeds have been developed to give you the
best possible tan, whilst complying with the
strictest applicable European standards.
Note:
Please consult enclosed tanning schedule for advised tanning times.
Repairs may only be carried out by qualifi ed personnel.
Always disconnect the main power at the circuit breaker before servicing or repairing the unit.
Read this fi rst
1 Contact your authorised Hapro dealer
immediately if this unit does not
function as outlined in this manual.
2 Do not operate this unit in humid
spaces.
3 Always make sure the fuses can carry
the load. This unit has to be protected
by ground fault circuit interrupter
(GFCI) of 0.03A.
4 Always disconnect the power to the
unit at the wall breaker (isolator)
when servicing or cleaning the in-
side construction of the cabine.
Maintenance for which the procedure
is not described in this manual should
only be carried out by a qualifi ed
electrician. Never clean the electrical
components with fl uids.
5 Ensure that the canopy does not touch
the wall when opened.
6 Prevent the acrylic sheets from coming
into contact with sharp objects.
7 This unit may not be operated if:
• the user is not wearing protective uv-
goggles
• the blue or white facial glass is cracked
or broken
• the acrylic panel in the canopy and/or
bench is missing
• one or more of the fans in the unit are
not functioning properly
• the timing mechanism is not
functioning properly
• the temperature inside the cabin is
30°C or higher
8 To ensure maximum tanning
eff ectiveness, change the acrylic sheet
after every 1200 hours of operation.
9 To ensure maximum tanning
eff ectiveness, replace the lamps and
the facial tanning lamps according to
manufacturer´s instructions.
10 Check local regulations to fi nd out the
proper procedure for lamp disposal.
11 Note: only a special acrylic cleaner
may be used to clean the acrylic sheet.
Never use cleaners that contain alcohol,
as these can damage the acrylic sheet.
12 The UV-type of the tanning unit is
indicated on the specifi cation sticker.
13 Ultraviolet radiation from the sun
or UV appliances can cause skin or
eye damage. These biological eff ects
depend upon the quality and quantity
of the radiation as well as the skin and
eye sensitivity of the individual.
14 Excessive exposure may cause skin to
burn. Excessive repeated exposure to
ultraviolet radiation from the sun or
UV appliances may lead to premature
ageing of the skin as well as increase
risk of skin tumours.
15 The unprotected eye may develop
surface infl ammation and in some
cases, after a cataract operation
for example, damage may accur to
the retina after eccessive exposure.
Cataracts may develop after prolonged
exposures.
16 If the supply cord is damaged, it must
be replaced by the manufacturer or
service agent or a similarly qualifi ed
person in order to avoid a hazard.
17 To replace lamps and starters, remove
by turning a quarter turn to the left.
Placement of new lamps and starters
is done in the reverse to the above
mentioned procedure.
18 When installing the equipment, follow
the recommended minimum distances
listed in the “Dimensions / Placement”
chapter.
19 Clean the dust fi lters after every 50
hours of use. Regularly check the dust
fi lters.
20 Children should be supervised to
ensure that they do not play with the
tanning unit.
21 Non-users, especially children, must
not be present when the appliance is
being operated.
‘The information contained in this manual regarding assembly and operation should be
followed in full. Failure to do so may render the product warranty or liability on behalf
of the supplier null and void. If there is any uncertainty as to whether the instructions
contained in this manual have been followed properly and entirely, you should contact
the supplier of the sunbeds.