Hanwha Techwin Wisenet PRN-4011 User Manual Download Page 52

Page: 52 / 88

failover

This function is only available for products that support failover. To find products that support this, see “

nvr

products supporting each feature

”. (Product Specification Manual, page 4)

Functions allowing other devices in a ready-state to perform recording if the NVR device can't perform

recording due to network error.
You can connect 32 “Normal” devices to one “Standby” device.

For a device to be configured for troubleshooting, both the camera and the viewer port must be connected to the local network.

All devices should be the same model when performing troubleshooting.

Troubleshooting network interface supports IPv4 only.

The time of all devices should be synchronized. For time sync setup, see the "

Menu Setup

System Setup

" page in the

Table of Contents.

The network IP bandwidth should be set differently in the NVR.

Example of IP in a different bandwidth

Example 1

) IP : 192.168.1.200, subnet 255.255.255.0

In the Example 1) above, since 255 of the subnet corresponds to 192.168.1, any IP in a format of

192.168.1.x has the same bandwidth.

An IP in a format of 192.168.2.x has a different bandwidth with an IP in a format of 192.168.1.x.

Example 2

) IP : 172.16.1.200, subnet 255.255.0.0

In the Example 2) above, since 255 of the subnet corresponds to 172.16, any IP in a format of 172.16.x.x

has the same bandwidth.

An IP in a format of 172.17.x.x has a different bandwidth with an IP in a format of 172.16.x.x.

For detailed network setup, see the "

Menu Setup

Network Configuration

" page in the Table of Contents.

to set troubleshooting

Set a device to 'Standby' and set the rest of the devices to 'Normal' mode.

Enter the viewer port ID and administrator's password of a 'Standby' device that you wish to connect from

a device set to a normal mode, and press the <

connection

> button under the status bar.

Check the IP and status of the 'Normal' devices connected to the 'Standby' device.

menu > network > failover

•

Mode : Select either <

normal

> or <

Standby

> mode.

- Normal : Device in recording operation. It is monitored by the Standby device.
- Standby : Device that is in a ready-state, not performing the recording operation. It performs the recording

operation instead of the Normal device that is out of order.

in the case of normal mode

•

Standby IP (All) : Enter the viewer port ID of a standby device to access.

•

Standby Password : Enter the administrator password of the standby device.

•

Status : Displays the current connection status.

•

Access or Disconnect button : Click the button to access or disconnect the access.

in the case of standby mode

•

Device list/Status: Shows the current state of the normal device(s) connected to the standby device. To delete

a connected normal device, click the <

delete

> button on the right side of the device.

For a Standby device, you can only use limited functions in the <

System Environment

>, <

Device

> and <

Network

menus. You can't use the <

Record

> and <

Event

> menus.

Activating the troubleshooting operation while playing a video or backing up a section in the Standby device will stop the

previous operation and a live image will be displayed.

State name

Descriptions

Ready

Ready to be connected

Connected

Normal and standby are connected (troubleshooting mode available)

Failover

Troubleshooting is being performed

Connected fail

Connection was attempted but failed

Authentication failure

Authentication failed due to incorrect standby password when attempting

connection

Connected(Match Time Required)

Connected but not time synchronized with the standby equipment

Connected(check camera port IP)

Situation in which the IP bandwidth of the camera port does not match even in a

case of connecting from the camera port of a normal device to the viewer port of a

standby device or to the port of the same viewer

Connected fail(check camera port IP)

Situation in which connection from the camera port of a normal device to the camera

port of a standby device has been attempted, but it failed to establish connection

Connected fail (It is a different model.)

Attempted to establish a connection between different models but failed to establish

connection

example) prn-4011

- Subnet 1 -> Network 1 (camera)
- Subnet 2 -> Network 2 (camera)
- Subnet 3 -> Network 3 (all)

REC

ALARM

POWER

BACKUP NETWORK

RAID

USB

HDD

REC

ALARM

POWER

BACKUP NETWORK

RAID

USB

HDD

REC

ALARM

POWER

BACKUP NETWORK

RAID

USB

HDD

Subnet 1 / Subnet 2

Normal

Standby

Subnet 3

Recording Stream
FailOver Monitoring
Fake Recording Stream

52_

menu setup

Summary of Contents for Wisenet PRN-4011

























































































Search results

Summary of Contents for Wisenet PRN-4011

Reviews:

Related manuals for Wisenet PRN-4011

Brands by name

Popular brands

Hanwha Techwin Wisenet PRN-4011, User Manual

Search results

Summary of Contents for Wisenet PRN-4011

Reviews:

Related manuals for Wisenet PRN-4011

Brands by name

Popular brands