Hansen APP08 Operator Installation & Instruction Manual Download Page 19

19

APP-001b

APR 2007

CAUTION

Hansen purgers are for refrigeration systems only. These 
instructions and related safety precautions must be read 
completely and understood before selecting, using, or 
ser vicing these purgers. Only knowledgeable, trained 
refrigeration technicians should install, operate, or service 
these purgers. Stated temperature and pressure limits 
should not be exceeded. Purger components should 
not be removed from the purger unless the system has 
been evacuated to zero pressure. See also the Safety 
Precautions in the current List Price schedule and the 
Safety Precautions Sheet supplied with this product. 
Escaping refrigerant can cause injur y, especially to the 
eyes and lungs.

WARRANTY

All Hansen products, except electronics, are guaranteed 

against defective materials or workmanship for one year 
F.O.B. factory. Electronics are guaranteed against defective 
materials or workmanship for 90 days F.O.B. factor y. No 

consequential damages or field labor is included.

ORDERING INFORMATION

Cat. No.

Description

APP08

AUTO-PURGER Plus, 8 points

APP16

AUTO-PURGER Plus, 16 points

APP24

AUTO-PURGER Plus, 24 points

APPC

AUTO-PURGER Plus for Plant 

Computer

To Order: Specify catalog number and voltage. 115V 

50/60Hz 17A is standard. 220V 50/60Hz 11A is available. 

All models are suitable for ammonia only.

Summary of Contents for APP08





















Reviews: