4.
Press the Right Key at the Calibrate Output 1A prompt. At the 20.000mA prompt
press Right Key once. Use the Up Key or the Down Key to adjust the display to
the reading on the volt/ammeter. The controller should stabilize within one
second. Repeat until the volt/ammeter reads 20.000mA. Press Right Key to
store the value.
Output 1B Milliamperes (Not Required)
Equipment
•
Precision volt/ammeter with 3.5-digit resolution.
Setup and Calibration
1.
Connect the correct power supply to terminals 1, 2 and 3 (see the Wiring
Chapter and the Appendix).
2.
Connect the volt/ammeter to terminals 39 (+) and 40 (-).
3.
Press the Right Key at the Calibrate Output 1B prompt. At the 4.000mA prompt
press Right Key once. Use the Up Key or the Down Key to adjust the display to
the reading on the volt/ammeter. The controller should stabilize within one
second. Repeat until the volt/ammeter reads 4.000mA. Press Right Key to store
the value.
4.
Press the Right Key at the Calibrate Output 1B prompt. At the 20.000mA prompt
press Right Key once. Use the Up Key or the Down Key to adjust the display to
the reading on the volt/ammeter. The controller should stabilize within one
second. Repeat until the volt/ammeter reads 20.000mA. Press Right Key to
store the value.
Output 2A Milliamperes (Not Required)
Equipment
•
Precision volt/ammeter with 3.5-digit resolution.
Setup and Calibration
1.
Connect the correct power supply to terminals 1, 2 and 3 (see the Wiring
Chapter and the Appendix).
2.
Connect the volt/ammeter to terminals 36 (+) and 37 (-).
3.
Press the Right Key at the Calibrate Output 2A prompt. At the 4.000mA prompt
press Right Key once. Use the Up Key or the Down Key to adjust the display to
the reading on the volt/ammeter. The controller should stabilize within one
second. Repeat until the volt/ammeter reads 4.000mA. Press Right Key to store
the value.
4.
Press the Right Key at the Calibrate Output 2A prompt. At the 20.000mA prompt
press Right Key once. Use the Up Key or the Down Key to adjust the display to
the reading on the volt/ammeter. The controller should stabilize within one
second. Repeat until the volt/ammeter reads 20.000mA. Press Right Key to
store the value.
Authorization and Copyright of this document is
controlled by Hanse Environmental Inc.
25
Summary of Contents for VTC Series
