Hama CONES 00173165, Operating Instructions Manual

Page: 4 / 39

3
Note – Charging/Battery level
• It takes approx. 5-6 hours to completely charge the product.
• The speaker’s battery can be charged whether the speaker is
on or off.
• If the battery level is less than 10%, an announcement will play.
You will only receive this information if the speaker is on.
• Depending on the terminal device connected ( Bluetooth
®
), the
speakers’ battery level will appear on the device.
• The actual battery life varies depending on use of the device, the
settings and the ambient conditions (rechargeable batteries have a
limited service life).
4.4 Audio playback via the included audio cable
(3.5 mm jack)
• Ensure that the speakers are switched off.
• Connect the 3.5 mm Y-audio cable to your terminal device (MP3
player, smartphone, computer, etc.) using the main connector
(somewhat thicker).
• Plug the two other connectors into the AUX-IN inputs (3) on the
speakers.
• Set the volume on your terminal device to a low level.
• Switch on the speakers as described in 4.1 Switching on/off the
product. The status LEDs (2) will flash steadily in blue.
• Start and control audio playback on the connected terminal device
accordingly.
Note
Please note that you cannot establish the
Bluetooth
®
connection
described under 4.5 and 4.6 if an audio cable is connected.
4.5 Bluetooth
®
pairing
Note
• Check whether your mobile device (MP3 player, mobile phone,
etc.) is
Bluetooth
® capable.
• If not, you can only use the speakers for playback using the
included audio cable.
• Note that the maximum range for Bluetooth
®
is 10 metres without
obstacles such as walls, people, etc.
• Make sure that your
Bluetooth
®
-capable terminal device is on and
Bluetooth
® is activated.
• Make sure that the speakers are located within the
Bluetooth
® range
of max. 10 metres.
• Switch on the speakers as described in 4.1. Switching on the product.
C
The speakers will search for a connection.
C
Alternatively you can press and hold the function buttons (5) on both
speakers at the same time until the status LEDs (1) alternate red and
blue flashes.
• Press and hold the function button (5) on the individual speaker until
the status LED (1) alternates red and blue flashes.
• Open the
Bluetooth
®
settings on your terminal device and wait until
Cones appears in the list of
Bluetooth
® devices found.
• Select Cones and wait until the speakers are listed as connected in
the Bluetooth
®
settings on your terminal device. An announcement
confirms that connection was successful.
C
The status LEDs (1) on both speakers will flash once in blue at regular
intervals.
• The status LED (1) on the individual speaker flashes once at regular
intervals.
Note – No connection possible
• If the speakers do not appear in the list of available devices,
quickly press the function button (5) twice in succession.
• A voice announcement plays and the speakers will search for a
connection to the terminal device.
Note –
Bluetooth
®
password
Some terminal devices require a password in order to connect to
another Bluetooth
®
device.
• If your terminal device requests a password for connection to the
speakers, enter 0000.
Note
• The speakers always store the last eight terminal devices paired.
• The speakers will automatically connect to the last terminal device
paired when it is switched on the next time.
• The speakers will exit pairing mode if no
Bluetooth
® connection
is established within two minutes. To activate pairing mode again,
see the section Note – No connection possible.
4.6 Automatic
Bluetooth
®
connection (after successful
pairing)
• Make sure that your Bluetooth
®
-capable terminal device is on and
Bluetooth
®
is activated.
• Make sure that the speakers are located within the
Bluetooth
®
range
of max. 10 metres.
• Switch on the speakers as described in section 4.5
Bluetooth
® pairing.
• An announcement confirms that connection was successful.
C
The status LEDs (1) on both speakers flash once in blue at regular
intervals.
• The status LED (1) on the individual speaker flashes once at regular
intervals.
Note – Connection impaired
• After the speaker and terminal device have been paired, a
connection is established automatically. If the Bluetooth
®
connection is not established automatically, check the following:
• Check the Bluetooth
®
settings of your terminal device to see
whether Cones is connected. If not, repeat the steps listed under
Bluetooth
® pairing.
• Check whether your terminal device and the speaker are less than
10 metres apart. If not, move them closer together.
• Check whether obstacles are impairing the range. If so, move the
devices closer together.
• Check whether the audio cable is connected to the speaker. If
so, disconnect it.