Halyard Exhaust Alert Mk3 Installation & Operating Instructions Manual Download Page 17

 

 

Exhaust Alert Operating & Fitting Instructions 

 

15 

HMI 201/01 

 

Section 6

 

Exhaust Alert Components 

Part No. 

Reference  Exhaust Alert System 

H020170 

AS701 

Master gauge with IP67 gland and hard wired 
3 metre harness. 

H020171 

AS702 

Repeater Gauge with IP67 gland and hard 
wired 3 metre harness

 

H021247 

AS115 

Single engine single station gauge with 
through hose sensor with 16 metre cable 

H021248 

AS125 

Single engine single station gauge with 
removable through hose sensor with 16 metre 
cable  

H021249 

AS135 

Single engine dual station gauge with through 
hose sensors with 16 metre cable  

H021250 

AS145 

Single engine dual station gauge with 
removable through hose sensors with 16 
metre cable 

H021251 

AS215 

Twin engine single station gauge with through 
hose sensor with 16 metre cable 

H021252 

AS225 

Twin engine single station gauge with 
removable through hose sensors with 16 
metre cable  

H021253 

AS235 

Twin engine dual station gauge with through 
hose sensors with 16 metre cable  

H021254 

AS245 

Twin engine dual station gauge with 
removable through hose sensors with 16 
metre cable 

H000447 

AS777 

Optional additional siren

 

 

 

 

 

Summary of Contents for Exhaust Alert Mk3





















Reviews: