background image

3

deemed liable for any damage resulting 
from unauthorized modifications to the 
vehicle.

This mashine is not suitable for 
evacuation of dusts, which are 
explosive or dangerous to 
health!

Notes on warranty

The terms defined in the purchase 
agreement apply. Claims for compen-
sation related to damage are excluded 
from the terms of warranty when the 
damage is the result of failure to ob-
serve regulations concerning service 
and maintenance. Maintenance work 
must be performed by authorized Hako 
service centers and confirmed in the 
“Maintenance Report” which serves as 
a warranty logbook. 

The following are excluded from the 
terms of warranty: wear and tear 
through overuse, defective fuses, im-
proper handling and use or unauthor-
ized modifications. Claims under the 
terms of warranty are annulled when 
damage occurs to the vehicle resulting 
from the use of parts or accessories not 
explicitly approved by us or from failure 
to observe maintenance regulations.

Acceptance of the vehicle

The vehicle must be inspected directly 
after delivery for signs of transport dam-
age. Replacements for transport dam-
age will be made when confirmation is 
provided immediately by the transport-
ing company with regard to the damage 
and you send the damage report to our 
authorized contractual partner together 
with the consignment note. 

Disposal

Render the vehicle inoperable. It must 
not represent a source of danger for 
children. Dispose of the equipment in 
accordance with local regulations. For 
further information on handling and re-
cycling, please contact the authorized 
Hako dealer where you purchased the 
vehicle. 

Used batteries with the recycling sym-
bol contain reusable commodities. The 
heavy metals contained represent a 
major risk both to people's health and to 
the environment. Never open or dam-
age batteries. Never touch, inhale or 

swallow the content of batteries. Health 
hazard! Do not allow batteries to get 
into the environment. Risk of contami-
nating the ground and water! In accor-
dance with symbol with the crossed out 
garbage bin, these batteries must not 
be disposed of in domestic waste. Re-
turn and recycling of old batteries must 
be agreed on with Hako's authorized 
dealers in accordance with § 6 and § 8 
BattG (Battery Law).

Introduction

Summary of Contents for Scrubmaster E10































Reviews: