HAKO Scrubmaster E10, Instruction Manual

Page: 18 / 30

18
Operation
Use the button to take the support
into working position.
Turn switch "A" ON to make the
brush rotate.
Turn switch "C" ON to open supply
of fresh water with or without deter-
gent. Press and hold switch "C" in
position "(1)" for simultaneous water
spraying.
Turn switch "B" ON to start suction
turbine running.
Turn all switches OFF after operation
and remove the brushes from the
Hakomatic. Mount the brushes in
inverse order of dismounting before
next operation. This measure extends
service life of the brushes.
Start operation of the
Hakomatic by pushing for-
ward immediately after
switching on. This measure
extends service life of the
brush motor. When pushing
in reverse direction lift the
rear squeegee with the
squeegee governor.
Make sure that during oper-
ation of the machine the
mains cable always lies
behind the operator.
Turn the brush drive off
before passing over dor-
mers of a height of 10mm
and more.
Danger when passing over
the mains cable with rotat-
ing brushes.
Start cleaning in the socket
area and clean by stripes. If
the surface is not obstruct-
ed, start at the borders and
forward counter-clockwise.
Clean the remaining surface
by stripes and starting in
the socket area.
Divide partly obstructed
surfaces into areas in the
reach of the mains cable.
Within shortest time, the
operator will know to avoid
unnecessary hindrance
caused by the mains cable.
At the end of cleaning:
Turn machine off and set it to its
park position
Empty and rinse soiled water tank
(see paragraph "Soiled and Fresh
Water Tanks")
Clean sealing strips of the squeegee
Check the sieve at the inlet opening
of the fresh water tank and clean if
required in order to maintain suction
performance.
Do not clean the machine
by means of a water jet or
high-pressure cleaning
equipment to avoid endan-
gering your safety and the
operability of the machine.
Operation
18
Operation
Use the button to take the support
into working position.
Turn switch "A" ON to make the
brush rotate.
Turn switch "C" ON to open supply
of fresh water with or without deter-
gent. Press and hold switch "C" in
position "(1)" for simultaneous water
spraying.
Turn switch "B" ON to start suction
turbine running.
Turn all switches OFF after operation
and remove the brushes from the
Hakomatic. Mount the brushes in
inverse order of dismounting before
next operation. This measure extends
service life of the brushes.
Start operation of the
Hakomatic by pushing for-
ward immediately after
switching on. This measure
extends service life of the
brush motor. When pushing
in reverse direction lift the
rear squeegee with the
squeegee governor.
Make sure that during oper-
ation of the machine the
mains cable always lies
behind the operator.
Turn the brush drive off
before passing over dor-
mers of a height of 10mm
and more.
Danger when passing over
the mains cable with rotat-
ing brushes.
Start cleaning in the socket
area and clean by stripes. If
the surface is not obstruct-
ed, start at the borders and
forward counter-clockwise.
Clean the remaining surface
by stripes and starting in
the socket area.
Divide partly obstructed
surfaces into areas in the
reach of the mains cable.
Within shortest time, the
operator will know to avoid
unnecessary hindrance
caused by the mains cable.
At the end of cleaning:
Turn machine off and set it to its
park position
Empty and rinse soiled water tank
(see paragraph "Soiled and Fresh
Water Tanks")
Clean sealing strips of the squeegee
Check the sieve at the inlet opening
of the fresh water tank and clean if
required in order to maintain suction
performance.
Do not clean the machine
by means of a water jet or
high-pressure cleaning
equipment to avoid endan-
gering your safety and the
operability of the machine.
Operation