Hach ORBISPHERE K-M1100 User Manual Download Page 33

Page: 33 / 116

Installation

3.7.3 Measurement board

3.8 Measurement alarm relays

Figure 16 Measurement board

Figure 17 Connector J7

Connector J7 (inputs & outputs)

Measurement alarms relays

Common

Output relay 1

Output relay 2

Output relay 3

Analog current (or voltage) outputs

Analog GND

Output 1

Output 2

Output 3

Digital inputs
9.

Hold input. To deactivate the sensor from
a PLC system, connect a dry contact
between J7.9 and J7.12

Note:

It is recommended to use this functionality in

order to extend the sensor lifetime for installations
with a CIP process that can damage the spot.

10.

Not used

11.

Not used

12.

Digital GND

13. to 16.

Not used

Figure 18 Output relays

The three output relays are located on the measurement
board.

They can be individually configured to Normally Open (NO) or
to Normally Closed (NC) by physically moving the jumper on
each relay. On the picture example on the left:

•

Upper relay is set to NC

•

Middle relay is set to NO

•

Lower relay is shown with no jumper

Note:

J14 (upper relay) is relay 1

J18 (middle relay) is relay 2
J19 (lower relay) is relay 3

Summary of Contents for ORBISPHERE K-M1100





















































































































Search results

Summary of Contents for ORBISPHERE K-M1100

Reviews:

Related manuals for ORBISPHERE K-M1100

Brands by name

Popular brands

Hach ORBISPHERE K-M1100, User Manual

Search results

Summary of Contents for ORBISPHERE K-M1100

Reviews:

Related manuals for ORBISPHERE K-M1100

Brands by name

Popular brands