manualshive.com logo in svg

H3C S5120-9P-SI, Installation Manual, Page: 55 / 73

Share
Download
H3C S5120-9P-SI Installation Manual Download Page 55

 

47 

Task Remarks 

Upgrading the Boot ROM file on the switch 

Required 
Upgrade the Boot ROM file on the switch. 

Restoring the download rate to the default 

Optional 
Set the baud rate of the serial port on the terminal to be 

consistent with the default rate of the console port on 
the switch. 

Restarting the switch to make the upgraded Boot ROM 

file effective 

Required 

 

1.

 

Enter the Boot ROM update menu on the switch 

Enter the Boot ROM menu, and then enter 

6

 or press 

Ctrl

 + 

U

 after the system displays “Enter your 

choice(0-9):” to enter the Boot ROM update menu.  

Enter your choice(0-9): 6 

 

1. Update full BootRom 

2. Update extended BootRom 

3. Update basic BootRom 

0. Return to boot menu 

 

Enter your choice(0-3): 

Table 19

 

Description of the Boot ROM update menu 

Item Description 

1. Update full BootRom 

Upgrade the complete Boot ROM file 

2. Update extended BootRom 

Upgrade the extended Boot ROM section 

3. Update basic BootRom 

Upgrade the basic Boot ROM section 

0. Return to boot menu 

Return to the Boot ROM menu 

 

2.

 

Enter the protocol parameter setting menu 

After the system displays “Enter your choice(0-3):”, enter 

1

 to enter the protocol parameter setting menu.  

 

 

NOTE: 

All the Boot ROM files to be loaded are complete Boot ROM files. 

 

1. Set TFTP protocol parameter 

2. Set FTP protocol parameter 

3. Set XMODEM protocol parameter 

0. Return to boot menu    

 

Enter your choice(0-3): 

Table 20

 

Description of the protocol parameter setting menu 

Item Description 

1. Set TFTP protocol parameter 

Set TFTP parameters 

Summary of Contents for S5120-9P-SI










































































Reviews:

No comments