H3C S5120-9P-SI Installation Manual Download Page 4

About the H3C S5120-SI documentation set 

The H3C S5120-SI documentation set includes: 

Category Documents 

Purposes 

Marketing brochures 

Describe product specifications and benefits.  

RPS Ordering Information for H3C 
Low-End Ethernet Switches 

Provides the RPS and switch compatibility matrix and 
RPS cable specifications.  

Product 
description and 

specifications 

H3C Low End Series Ethernet 
Switches Pluggable Modules 

Manual 

Describes the models, appearances, and 
specifications of the pluggable modules available for 

the products.  

Quick Start Guide 

Provides a quick guide to hardware installation. 

Installation Manual 

Provides a complete guide to hardware installation 
and hardware specifications. 
Provides regulatory information and the safety 

instructions that must be followed during installation. 

Hardware 
installation 

Pluggable SFP[SFP+][XFP] 
Transceiver Modules Installation 

Guide 

Guides you through installing SFP/SFP+/XFP 
transceiver modules. 

Configuration guides 

Describe software features and configuration 
procedures. 

Software 
configuration 

Command references 

Provide a quick reference to all available commands. 

H3C Series Ethernet Switches 

Login Password Recovery Manual  Describes how to find or recover a lost password.  

Operations 

and 
maintenance 

Release notes 

Provide information about the product release, 
including the version history, hardware and software 
compatibility matrix, version upgrade information, 

technical support information, and software 

upgrading. 

 

Obtaining documentation 

You can access the most up-to-date H3C product documentation on the World Wide Web at 

http://www.h3c.com

Click the links on the top navigation bar to obtain different categories of product documentation: 

[Technical Support & Documents > Technical Documents]

 – Provides hardware installation, software 

upgrading, and software feature configuration and maintenance documentation. 

[Products & Solutions]

 –

 

Provides information about products and technologies, as well as solutions.

 

[Technical Support & Documents > Software Download]

 – Provides the documentation released with the 

software version. 

Technical support 

[email protected] 

Summary of Contents for S5120-9P-SI










































































Reviews: