H3C DSIC-9FSW Manual Download Page 64

Page: 64 / 219

MIM-1GEF/MIM-2GEF

Introduction

The 1/2-port 1000Base-SX/1000Base-LX GE optical interface module (MIM-1GEF/MIM-2GEF) is
used for the communication between router and LAN.

MIM-1GEF/MIM-2GEF supports:

•

Various types of transceiver modules.

•

1000 Mbps interface rate.

•

Full duplex.

Interface specifications

Table 75 Interface specifications

Item MIM-1GEF MIM-2GEF

Number of interfaces

Connector SFP/LC

Interface standard

802.3, 802.3u, 802.3ab

Operating mode

1000 Mbps
Full duplex

Interface LEDs

Figure 59 MIM-1GEF panel

Figure 60 MIM-2GEF panel

Table 76 LED description

LED Description

LINK

•

Off: No link is present.

•

On: A link is present.

ACT

•

Off: No data is being transmitted or received.

•

Flashing: Data is being received or/and transmitted.

Summary of Contents for DSIC-9FSW




























































































































































































































Search results

Summary of Contents for DSIC-9FSW

Reviews:

Related manuals for DSIC-9FSW

Brands by name

Popular brands

H3C DSIC-9FSW, Manual

Search results

Summary of Contents for DSIC-9FSW

Reviews:

Related manuals for DSIC-9FSW

Brands by name

Popular brands