H3C DSIC-9FSW Manual Download Page 66

Page: 66 / 219

Interface LEDs

Figure 61 MIM-1ATM-OC3 panel

Table 78 LED description

LED Description

LINK/ACT

•

On: Carrier signal has been received.

•

Flashing: Data is being received or/and transmitted.

•

Off: No carrier signal has been received.

LP/AL

•

On: The interface is in a loopback.

•

Off: No loopback or alarm is present.

•

Flashing: An alarm indication signal (AIS), loss of frame alignment
(LFA) signal, or remote alarm indication (RAI) signal is present.

Transceiver modules, optical fibers, and connection methods

For more information about transceiver modules, optical fibers, and the connection methods, see
"

Fiber port

MIM-1AE3

Introduction

The 1-port 34.368 Mbps ATM-E3 interface module (MIM-1AE3) supports:

•

Two ATM cell mapping modes: ATM Direct Mapping (ADM) and Physical Layer Convergence
Protocol (PLCP)

•

Scrambling in data transmission

•

Both line clock (when working as DTE interface) and internal clock (when working as DCE
interface)

•

Four types of test measures: local cell loopback, local payload loopback, remote payload
loopback, and remote line loopback

Interface specifications

Table 79 Interface specifications

Item Description

Connector SMB

Connector number

Summary of Contents for DSIC-9FSW




























































































































































































































Search results

Summary of Contents for DSIC-9FSW

Reviews:

Related manuals for DSIC-9FSW

Brands by name

Popular brands

H3C DSIC-9FSW, Manual

Search results

Summary of Contents for DSIC-9FSW

Reviews:

Related manuals for DSIC-9FSW

Brands by name

Popular brands