H3C DSIC-9FSW Manual Download Page 123

Page: 123 / 219

114

Table 159 LED description

LED Description

LINK/ACT

•

Off: No link is present;

•

On: A link is present.

•

Flashing: Data is being received or transmitted.

LP/AL

•

On: A loopback interface is configured.

•

Flashing: An alarm indication signal (AIS), loss of frame alignment (LFA)
signal, or remote alarm indication (RAI) signal is present.

Transceiver modules, optical fibers, and connection methods

For more information about transceiver modules, optical fibers, and the connection methods, see
"

Fiber port

Interface mode switchover

You can switch the FIC-1CPOS to operate in E1 and T1 interface modes at the command line
interface (CLI).

To switch the interface mode:

Insert the FIC-1CPOS into the FIC slot of the router and then power on the router.

Use the

card-mode

command in system view to set the interface mode. The following shows

the FIC-1CPOS module is inserted in slot 4 of the device.

# Enter system view.

<Sysname> system-view

# Set the FIC-1CPOS to operate in E1 interface mode.

[Sysname] module-mode slot 4 e1

# Set the FIC-1CPOS to operate in T1 interface mode.

[Sysname] module-mode slot 4 t1

E1/T1 interface module

•

FIC-1E1

•

FIC-2E1

•

FIC-4E1

•

FIC-1E1-F

•

FIC-2E1-F

•

FIC-4E1-F

•

FIC-8E1

•

FIC-8E1-F

•

FIC-1T1

•

FIC-2T1

Summary of Contents for DSIC-9FSW




























































































































































































































Search results

Summary of Contents for DSIC-9FSW

Reviews:

Related manuals for DSIC-9FSW

Brands by name

Popular brands

H3C DSIC-9FSW, Manual

Search results

Summary of Contents for DSIC-9FSW

Reviews:

Related manuals for DSIC-9FSW

Brands by name

Popular brands