manualshive.com logo in svg

GVS KI/U 0401.1, User Manual, Page: 53 / 53

Share
Download
GVS KI/U 0401.1 User Manual Download Page 53

K-BUS

®

KNX/EIB

Universal Interfaces

50

6.10. Communication object “LED X-Switch”

The communication object “LED X—Switch” will be shown in Fig.6.10

Fig.6.10 Communication object “LED X-Switch”

No.

Function

Object name

Date type

Flags

DPT

28

LED X Switch

LED. switch, X

1Bit

C,W

1.001 switch

This communication object is used to open LED. It will open LED if the object receive a “1” or “0” telegram (defines by

“LED is Switch ON

，

if”

）

，

the open time can be set by parameter

；

it will stop LED if receive “0” or “1”.

29

LED X Permanent on

LED permanent on, X

1Bit

C,W

1.001 switch

It is used to open LED for a long period and its priority is higher than the communication object “LED. switch, X”. It will

open LED if receive telegram “1”, negate priority and the LED resume the foregoing operation if receive “0”.

30

LED X Send its status

Send its status, X

1Bit

C,T

1.001 switch

It is visible if “Send status by object “Tele. Status”” selected “Yes”

，

it is used to send the status of LED. Sending “1”

means LED open, and sending “0” means the LED is stop. The object LED. switch, X” will send telegram “1” if sending
open requirement every time.

Form 10 Communication object “LED X-Switch”

Summary of Contents for KI/U 0401.1






















































Reviews:

No comments