manualshive.com logo in svg

GVS KI/U 0401.1, User Manual, Page: 40 / 53

Share
Download
GVS KI/U 0401.1 User Manual Download Page 40

K-BUS

®

KNX/EIB

Universal Interfaces

37

Parameter “LED Flashing, if”

This parameter defines the mode of opening the LED flashing.Options:

Object “LED flashing”=0

Object “LED flashing”=1

Parameter “Time limit of LED control”

This parameter defines whether to enable the function to restrict the flashing of the LED.Options:

No
Yes

Parameter “Time limit: Base× Factor

This parameter is visible if the time limit is active. It is defines the time of LED flashing: Base×

Factor.

Base options:

1s

10s
…
1h

Factor options:

1…255

Parameter “Send status by object “Tele. Status””

This parameter defines whether to send the LED status report on the bus.Options:

No
Yes

If “Yes” is selected, the object “Send its status, X” will send value “1” when LED flashing; it will send

value “0” when LED stop flashing.

Parameter “State of LED on bus voltage recovery”

It is defines the state of LED when the bus voltage recovery.Options:

On
Off

Parameter “LED is switched ON/OFF for”

It is defines the time of the LED switched on/off when LED flashing.Options:

600ms
800ms
……
60s

Summary of Contents for KI/U 0401.1






















































Reviews:

No comments