manualshive.com logo in svg

GVS KI/U 0401.1, User Manual, Page: 52 / 53

Share
Download
GVS KI/U 0401.1 User Manual Download Page 52

K-BUS

®

KNX/EIB

Universal Interfaces

49

6.8. Communication object “Shutter control”

The communication object “Shutter Control” will be shown in Fig.6.8

Fig.6.8 Communication object “Shutter control”

No.

Function

Object name

Data type

Flags

DPT

1

CH X shutter UP/DOWN

Output shutter UP/DOWN, X 1Bit

C,T

1.008 up/down

This communication object move up/down the shutter by sending command by bus. It will move down if the

communication object send a “1” telegram, it will move up if sending a “0”.

2

CH X Stop/adjust adj

Output Stop/adjust adj, X

1Bit

C,T

1.007 step

It will stop/adjust the shutter by sending command by bus. It will stop/ adjust down if sending a “1” telegram, and it will

stop/adjust up if sending “0”.

3

CH X Upper limit position

Upper limit position, X

1Bit

C,W

1.003 enable

It is used to limit the upper moving. It is limit the upper moving if the object receive a logic value “1”, and negate it if

receive “0”.

4

CH X Lower limit position

Lower limit position, X

1Bit

C,W

1.003 enable

It is used to limit the lower moving. It is limit the lower moving if the object receive a logic value “1”, and negate it if

receive “0”.

Form 8 Communication object “Shutter control”

6.9. Communication object “LED X-flashing”

The communication object “LED X—Flashing” will be shown in Fig.6.9.

Fig.6.9 Communication object “LED X-Flashing”

No.

Function

Object name

Data type

Flags

DPT

28

LED X Flashing

LED. Flashing, X

1Bit

C,W

1.001 switch

It is used to control the LED flashing. It will start flashing if receive “1” or “0” telegram (defines by “LED flashing, if”), the

flashing time set by parameter. And it will stop LED if receive “0” or “1”.

29

LED X Permanent on

LED permanent on, X

1Bit

C,W

1.001 switch

It is used to open LED for a long period and its priority is higher than the communication object “LED. Flashing, X”. It

will open LED if receive telegram “1”, negate priority and the LED resume the foregoing operation if receive “0”.

30

LED X Send its status

Send its status, X

1Bit

C,T

1.001 switch

It is visible if “Send status by object “Tele. Status”” selected “Yes”

，

it is used to send the status of LED. Sending “1”

means LED open or flashing, and sending “0” means the LED is stop. The object LED. Flashing, X” will send telegram “1” if
sending open flashing requirement every time.

Form 9 Communication object “LED X-Flashing”

Summary of Contents for KI/U 0401.1






















































Reviews:

No comments