GÜDE Expert PDU Energy 8311 Series Manual Download Page 6 | Manualshive

Page: 6 / 81

background image

6

Expert PDU Energy 8311

© 2021 GUDE Systems GmbH

Device Description

1

Device Description

1.1

Security Advice

·

The device must be installed only by qualified personnel according to the following
installation and operating instructions.

·

The manufacturer does not accept responsibility in case of improper use of the
device and particularly any use of equipment that may cause personal injury or ma-
terial damage.

·

The device contains no user-maintenable parts. All maintenance has to be per-
formed by factory trained service personnel.

·

This device contains potentially hazardous voltages and should not be opened or
disassembled.

·

The device can be connected only to 230V AC (50 Hz or 60 Hz) power supply sock-
ets.

·

The power cords, plugs and sockets have to be in good condition. Always connect
the device to properly grounded power sockets.

·

The device is intended for indoor use only. Do NOT install them in an area where ex-
cessive moisture or heat is present.

·

Because of safety and approval issues it is not allowed to modify the device without
our permission.

·

The device is NOT a toy. It has to be used or stored out of range of children.

·

Care about packaging material. Plastics has to be stored out of range of children.
Please recycle the packaging materials.

·

In case of further questions, about installation, operation or usage of the device,
which are not clear after reading the manual, please do not hesitate to ask our sup-
port team.

·

Please, never leave connected equipment unattended, that can cause damage.

·

Connect only electrical devices that do not have limited on-time. I.e. in case of
failure, all connected appliances have to cope with a continuous on-time without
causing damage.

1.2

Content of Delivery

The package includes:

·

Expert PDU Energy 8311

·

Quick Start Guide

1.3

Description

The

Expert PDU Energy 8311

multiple socket outlet with 7 load outputs. The device

has the following features:

·

Metering of energy, current, power factor, phase angle, frequency, voltage and act-
ive/apparent/reactive power

·

Two energy meters, one meters continously, the other energy meter is resettable

·

Measurement of residual current type A (

model 8311-2

).

·

Illuminated two-line LCD display

«
...
4
5
6
7
8
...
»

Summary of Contents for Expert PDU Energy 8311 Series


















































































Reviews:

No comments

Related manuals for Expert PDU Energy 8311 Series

Brand: RAMSET Pages: 18

Brand: Geberit Pages: 262

Brand: Patterson Pages: 16

Brand: NKO MACHINES Pages: 16

Brand: RIDGID Pages: 43

Brand: VOLTCRAFT Pages: 8

Brand: Hama Pages: 48

Brand: Ubermann Pages: 40

Brand: Panduit Pages: 2

Brand: Xantrex Pages: 76

Brand: Parkside Pages: 12

Brand: BE QUIET! Pages: 51

Brand: tekton Pages: 8

Brand: MAC TOOLS Pages: 32

PALMER POWER STATION

Brand: M2TECH Pages: 11

Brand: Narex Pages: 44

Brand: Baileigh Industrial Pages: 28

FORCEDRIVER WX270L

Brand: Worx Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands