manualshive.com logo in svg

GÜDE Expert PDU Energy 8311 Series, Manual

Share
Download
GÜDE Expert PDU Energy 8311 Series Manual Download Page 57

57

Expert PDU Energy 8311 

 

                                                                                                                                                                                         © 2021 GUDE Systems GmbH

Specifications

commands sent at the beginning can appear as interfering characters in the command
line (partially invisible).

Editing

The following edit functions are available when the terminal supports VT100, and Raw
Mode is deactivated. Entered characters are inserted at the cursor position.

Keys

Function

 Left, Right

 moves cursor left or right

 Pos1, End

 moves cursor to the beginning or end of line

 Del

 deletes character under the cursor

 Backspace

 deletes character left of cursor

 Up, Down

 shows input lines history

 Tab, Ctrl-Tab

 completes the word at cursor

Ctrl-C

clears the line

 

Sensor Examples

a) External Sensors

>extsensor all show
E=1,L="7106",0="21.3°C",1="35.1%",3="1013hPa",4="5.2°C",5="16.0°C""
E=2,L="7102",0="21.2°C",1="35.4%",4="5.3°C",5="15.9°C""

The command lists one connected external sensor per line, and the individual meas-
ured values are separated by commas after the label name. The digit before the equal
sign corresponds to the Index field in the External Sensor Table.

>extsensor 1 0 value show

Displays temperature of the sensor at Port 1

b) Line Sensors

>linesensor all "0,1,2,3,12" show
L=1,L="Power Port",0="13000Wh",1="0W",2="225V",3="0A",12="998218s"
L=2,L="Power Port",0="13000Wh",1="0W",2="223V",3="0A",12="996199s"

This command outputs all line sensor values in one line. A list of all fields (according to
the energy sensor table) is transferred as parameter. In this example these are the
fields Absolute Active Energy (0), Power Active (1), Voltage (2), Current (3) and Reset
Time (12).

>linesensor 1 

"0,1,2,3,12"

 show

>linesensor 1 1 show

These variants give the sensor values of the field list or of a sensor at Line-In 1.

 For devices with Overvoltage Protection, the "linesensor all" command also outputs

the state of the protection ("OVP=x"). A "1" means ok, a "0" a failure of the protection.

c) Port Sensors

>portsensor all "0,1,2,3,12" show
P=1,L="Power Port",0="13000Wh",1="0W",2="225V",3="0A",12="998218s"

Summary of Contents for Expert PDU Energy 8311 Series


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands