manualshive.com logo in svg

GÜDE Expert PDU Energy 8311 Series, Manual

Share
Download
GÜDE Expert PDU Energy 8311 Series Manual Download Page 41

41

Expert PDU Energy 8311 

 

                                                                                                                                                                                         © 2021 GUDE Systems GmbH

Configuration

3.4

Sensors

Sensor: Selects a type of sensor to configure it. The first digit "1" indicates the number
of the sensor port (only important for devices with more than one sensor port). This is
followed by the sensor name, and the changeable sensor name.

Sensor Name: Changeable name for this sensor. Temperature and humidity can have
different names, even if they are from the same sensor.

Select Sensor Field: Selects a data channel from a sensor.

Enable ... Messages: Enables the generation of sensor messages.
Maximum/Minimum value: Here you can choose whether, and at what Maximum/Min-
imum temperature or humidity measurements limits the alerts are send via SNMP
traps, syslog or e-mail.

Hysteresis: This describes the margin of when an event is generated after the meas-
ured value has crossed the chosen limit.

Message channels: Enables the generation of messages on different channels.

With the beeper you can choose between a continuous or an intermittent tone. Flash-
ing display changes the brightness of the LCD backlight in cylcles. By pressing a front
panel button the beeper and the flashing display will be reset.

Console push-messages

: 

This option allows the output of sensor values on the con-

sole at a configured time interval, or when a certain threshold has been reached.

Min/Max measurement period: Selects the time range for the sensor min/max values
on the overview web page.

Summary of Contents for Expert PDU Energy 8311 Series


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands