manualshive.com logo in svg

GSS PTIS 1000, Assembly Instructions Manual, Page: 20 / 35

Share
Download
GSS PTIS 1000 Assembly Instructions Manual Download Page 20

 

 

- 20 - 

PTIS 1000

 

•  Use the

 

 buttons to place the cursor under the digit of the port number 

displayed to be set and use 

 to set the port number wished ("

0

" … 

"

65535

").

 

•  Press the 

 button.

 

—>  The "Selecting the input transport stream" – "

INPUT

" menu is activated.

 

Selecting the input transport stream

 

In this menu you select the signal source for the selection of the services. The 

transport streams to be processed are provided by "

Tuner A

", "

Tuner B

" and 

the ASI interface "

ASI

".

Bx 4A
Lan

INPUT

 

•  Press the 

 buttons to select the signal source of the input transport 

stream ("

Tuner A

", "

Tuner B

", "

ASI

"). 

 

—>  "

OK

" indicates that an input signal is present. If there is no input signal 

available "

– –

" is displayed instead of "

OK

".

 

Input transport stream selected: "

ASI

"

 

•  Press the 

 button.

 

—>  The menu "Allocating IP addresses" – "

IP-OUT 1

" is activated (page 23).

 

Input transport stream selected: "

Tuner A

" or "

Tuner B

"

 

•  Press the 

 button.

 

—>  The menu "Setting the input channel" – "

INPUT

" is activated. 

Summary of Contents for PTIS 1000




































Reviews:

No comments