GSi 40 Series Construction Manual Download Page 86

Page: 86 / 116

Chapter 8: Roof Assembly

Installing the Manway Cover

Installation of a manway cover is necessary if a manway hole is present.

Round manway cover details for bins for bins 60' and smaller.

1. Apply caulking to the underside of the moisture diverter (N), and install to the manway roof

panel (L).

2. Install the hinge base (A) to the moisture diverter (N), and install three 5/16 x 1 in. flange bolts (K)

and 5/16 in. flange nuts (H).

3. Install the handle gasket (F) and the handle (E) to the manway cover (G), and secure with two #10

long bolts (D) and lock nuts (J).

4. Install the latch (I) to the handle (E) using a 5/16 x 1 in. flange bolts (C) and 5/16 in. flange nuts (H).

5. Install the hinge leaf (B) to the manway cover (G) and secure all four 5/16 x 1 in. flange bolts (C) and

5/16 in. flange nuts (H). Install the manway assembly to the hinge base (A), and secure with two
5/16 x 1 in. flange bolts (K) and 5/16 in. flange nuts (H).

NOTE:

When securing the hinge leaf (B) to the hinge base (A), double nut each hex bolt.

6. Tighten hardware to the recommended torque specifications. See

Bolt Torque Specifications, page

7. Affix suffocation/flighting decals (not shown) to the underside of the manway cover (G).

NOTE:

Suffocation/flighting decals replacement part numbers: English, DC-GBC-1A and Spanish,
DC-GBC-1S.

8. Snap the manway seal strip (M) onto the lip of the manway hole.

9. Make the necessary adjustments to the handle (E) and latch (I), creating a tight seal.

PNEG-4336

36 Ft. Diameter 40-Series Bins

Summary of Contents for 40 Series





















































































































Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands

GSi 40 Series, Construction Manual

Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands