GSi 40 Series Construction Manual Download Page 110

Page: 110 / 116

Chapter 9: Accessories

Assembling Weather Cover for Roller Valve

The following instructions are for assembling the weather cover for the roller valve.

1. Install the weather cover kit after the gate has been installed.

2. Use bead caulking at all seams where the weather cover attaches to the gate.

3. Use 5/16 x 1 in. flange bolts (C) and 5/16 in. flange nuts (D) to plug all holes not in use.

4. Use 1/4 in. self-drilling screw (B) to seal gate end plate corners.

Figure 9-17

Weather cover assembly

Universal weather cover plate (CHT-1351)

5/16 in. flange nut (S-3611)

1/4 in. self-drilling screw (S-6497)

Universal weather cover plate (CHT-1351)

5/16 x 1 in. flange bolt with sealing washer
(S-10260)

Chain wheel (typical)

110

PNEG-4336

36 Ft. Diameter 40-Series Bins

Summary of Contents for 40 Series





















































































































Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands

GSi 40 Series, Construction Manual

Search results

Summary of Contents for 40 Series

Reviews:

Related manuals for 40 Series

Brands by name

Popular brands