background image

13

Eng

lish (US

)

chapter discard.fm  Page 13  Tuesday, June 7, 2011  9:29 PM

LIMITED WARRANTY

Products  manufactured  by  GRUNDFOS  PUMPS  CORPORATION  (GRUNDFOS)    are  warranted 
to  the  original  user  only  to  be  free  of  defects  in  material    and  workmanship  for  a  period  of 
24  months  from  date  of  installation,  but  not  more  than  30  months  from  date  of  manufac-
ture.  GRUNDFOS’  liability  under  this  warranty  shall  be  limited  to  repairing  or  replacing  at
GRUNDFOS’  option,  without  charge,  F.O.B.  GRUNDFOS’  factory  or  authorized  service  sta-
tion, any product of GRUNDFOS’ manufacture. GRUNDFOS will not be liable for any costs of 
removal, installation, transportation, or any other charges which may arise in connection with 
a warranty claim. Products which are sold but not manufactured by GRUNDFOS are subject to 
the warranty provided by the manufacturer of said products and not by GRUNDFOS’ warranty. 
GRUNDFOS will not be liable for damage or wear to products caused by abnormal operating 
conditions, accident, abuse, misuse, unauthorized alteration or  repair, or if the product was 
not installed in accordance with GRUNDFOS’ printed installation and operating instructions.

To  obtain  service  under  this  warranty,  the  defective  product  must  be  returned  to  the
distributor  or  dealer  of  GRUNDFOS’  products  from  which  it  was  purchased  together  with 
proof of purchase and installation date, failure date, and supporting installation data. Unless
otherwise provided, the distributor or dealer will contact GRUNDFOS or an authorized service 
station for instructions. Any defective product to be returned to GRUNDFOS or a service station 
must be sent freight prepaid; documentation supporting the warranty claim and/or a Return 
Material Authorization must be included if so instructed.

GRUNDFOS  WILL  NOT  BE  LIABLE  FOR  ANY  INCIDENTAL  OR  CONSEQUENTIAL  DAMAGES, 
LOSSES,  OR  EXPENSES  ARISING  FROM  INSTALLATION,  USE,  OR  ANY  OTHER  CAUSES.  THERE 
ARE NO EXPRESS OR IMPLIED WARRANTIES, INCLUDING MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, WHICH EXTEND BEYOND THOSE WARRANTIES DESCRIBED OR REFERRED 
TO ABOVE.

Some  jurisdictions  do  not  allow  the  exclusion  or  limitation  of  incidental  or  consequential
damages  and  some  jurisdictions  do  not  allow  limitations  on  how  long  implied  warranties 
may last. Therefore, the above limitations or exclusions may not apply to you. This warranty 
gives you specific legal rights and you may also have other rights which vary from jurisdiction
to jurisdiction.

Summary of Contents for HS 100 0505

















Reviews: