GrowSpan 106201 Instructions Manual Download Page 6

Page: 6 / 49

GROWSPAN

™

ROUND PREMIUM GREENHOUSES

106201_02_03_04

Revision date: 01.10.19

H-CHANNEL INSTALLATION INSTRUCTIONS

The new H-channel design requires installation of flat side facing out with channel side toward build

ing. Some diagrams and photos in this document may show installation of

original

H-channel with

channel side facing out.

Design of new H-channel does not allow channel-side out installation.

Use the diagrams on this page to install H-channel with flat side facing out.

ATTENTION:

Use only 1-1/2" Tek screws to attach H-channel to building frame.

Do not use

shorter screws. They will not hold. Do not use washers on Tek screws when installing

the 113236Z096 H-channel.

ATTENTION:

Install all twin-wall polycarbonate panels with UV-protected side toward the sun.

UV-protected side

toward sun.

Install 1-1/2" Tek screws through

H-channel into building frame.

H-Channel

Center Groove

Flat side toward the sun.

Flat

Side

Channel

ASSEMBLY NOTE:

Install Tek screws using a clutched drill driver running

approximately 750 RPM while applying approximately 50 lbs of force.

Do not use an impact driver to install Tek screws!

Summary of Contents for 106201


















































Search results

Summary of Contents for 106201

Reviews:

Related manuals for 106201

Brands by name

Popular brands

GrowSpan 106201, Instructions Manual

Search results

Summary of Contents for 106201

Reviews:

Related manuals for 106201

Brands by name

Popular brands