Grizzly T33300 Owner'S Manual Download Page 7

Model T33300 (Mfd. Since 04/22)

-5-

The following is a list of common definitions, terms and phrases used throughout this manual as they relate 
to this track saw and woodworking in general. Become familiar with these terms for assembling, adjusting 
or operating this tool. Your safety is 

VERY important to us at Grizzly! 

Arbor:  Metal  shaft  extending  from  the  drive 

mechanism,  to  which  saw  blade  is  mounted. 
The blade is held in place on the arbor using a 
special arbor bolt and arbor washer.

Bevel Edge Cut:  Tilting  the  saw  blade  to  an 

angle  between  0°  and  45°  to  cut  a  beveled 
edge onto a workpiece.

Blade Guard: Metal or plastic safety device that 

encases the saw blade. Its function is to pre-
vent the operator from coming into contact with 
the saw blade.

Kerf:  The  resulting  cut  or  gap  in  the  workpiece 

after  the  saw  blade  passes  through  during  a 
cutting operation.

Kickback: An event in which the tool is propelled 

back  towards  the  operator  at  a  high  rate  of 
speed. 

Parallel: Being an equal distance apart at every 

point  along  two  given  lines  or  planes.  I.e.  the 
rip fence face is parallel to the face of the saw 
blade.

Perpendicular:  Lines  or  planes  that  intersect 

and form right angles. I.e. the blade is perpen-
dicular to the table surface.

Plunge Cut:  A  sawing  operation  in  which  the 

cut  is  started  above  the  workpiece;  the  blade 
engages the workpiece by "plunging" down at 
the  beginning  of  the  cut,  and  advances  once 
the blade cuts through the workpiece.

Rip Cut: Cutting operation in which the rip fence 

is used to cut with the grain, or across the wid-
est width of the workpiece.

Riving Knife:  Metal  plate  located  behind  the 

blade. It maintains the kerf opening in the wood 
when performing a cutting operation.

Straightedge: A tool used to check the flatness, 

parallelism, or consistency of a surface(s).

Through Cut:  A  sawing  operation  in  which  the 

workpiece is completely sawn through.

Glossary Of Terms

Summary of Contents for T33300





































Reviews: