Grizzly G0845P Owner'S Manual Download Page 49

Page: 49 / 68

Model G0845P (Mfd. Since 01/18)

-47-

5. Install (4) new V-belts as a set.

6. Lift motor up, then replace spherical washer

and upper hex nut removed in

Step 4.

6. Tension belts (refer to Tensioning V-Belts

on this page.)

7. Replace front cover.

4. Remove upper hex nut and spherical washer

at top of motor mount shaft (see

Figure 72).

Tighten lower hex nut to shift motor down for
clearance to roll V-belts off gearbox pulley.

3. Loosen hex bolt and hex nut that pass

through motor mount shaft (see

Figure 71).

Figure 71. Loosening motor to remove V-belts.

V-Belts

Upper

Hex

Nut

Hex Nut

Motor

Mount

Shaft

Lower

Hex

Nut

Hex Bolt

OFF

Figure 72. V-belt removal from gearbox pulley.

Motor Mount Shaft

Lower Hex Nut

Gearbox Pulley

Adjusting V-Belt Tension

1. DISCONNECT MACHINE FROM POWER!

2. Loosen hex bolt and hex nut that pass

through  bottom  of  motor  mount  shaft,  then
loosen  lower  hex  nut  and  tighten  upper  hex
nut  in  equal  amounts  to  tighten  belts  until
deflection equals

⁄

" (see

Figure 70).

Note: If belt deflection cannot be adjusted
to equal

⁄

", replace all four belts. Refer to

Replacing V-Belts.

3. After properly tensioning belts, tighten all

nuts and bolts.

4. Replace front cover.

Figure 70. Adjusting motor mount shaft upward

to tighten V-belt tension.

V-Belts

Upper

Hex

Nut

Hex Nut

Motor

Mount

Shaft

Lower

Hex

Nut

Hex Bolt

OFF

Replacing V-Belts

1. DISCONNECT MACHINE FROM POWER!

2. Remove front cover.

Summary of Contents for G0845P





































































Search results

Summary of Contents for G0845P

Reviews:

Related manuals for G0845P

Brands by name

Popular brands

Grizzly G0845P, Owner'S Manual

Search results

Summary of Contents for G0845P

Reviews:

Related manuals for G0845P

Brands by name

Popular brands